Disposal Of The Product - Maxell YOSO PRO Manual Del Usuario

It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "LOW."
4 Hold the device with your hand touching the back plate of the body. (Fig. 7)
●
Make sure to hold the body with your hand touching the back plate.
5 Apply and move the head slowly. (Fig. 8)
When using a sheet mask, slide the head over the sheet mask.
●
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
●
The time for use is within 5 minutes.
CAUTION
Unless you apply the head to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the head is not vibrating, the device is not working.
If you leave the device as it is for about 5 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
● Apply the head gently to the face and slowly move the device by sliding it from
the center of the face to the outer side.
Do not keep the head in the same area of the skin, but move it
around. (Cause of problems with your skin or poor health)
●
Do not apply the device on the same area of skin for more than 10 seconds.
● If you feel your skin tingling by micro current while using the device, press the level
switch button and switch to "Low."
6 After 5 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
● The finish sound (beep beep) will inform you.
7 Wipe off the moisturizing product on the head and the body of the device with a tissue.
How to use with AC
Avoid using in a place where water is splashed such as a bathroom
or in a place with high moisture.
(Cause of electric shocks and short circuits)
1 Connect the power adaptor to the main body and outlet.
● Follow "How to use" for use.
While the device is being used, the battery indicator lamp will be off.
2 Make sure to pull out the power adaptor from the outlet and the body.
About skin sensing function
This device is a product which operates through the human body.
Applying the skin to the back plate and the head will make an electrical circuit start to
operate. Unless you touch the back plate and apply the head to the skin, it will not start
to operate.
About memory function
This device is equipped with a memory function to store memory of the electrical
potential "strength" levels of "HIGH," "MEDIUM," or "LOW".
In each usage mode (Step 1 to 3), the device stores memory of the "strength" level just
before the automatic shutoff or the power switch is turned "off."
If the level switch button is pressed while the device is being used, the electric potential
"strength" can be switched.
-11-
All manuals and user guides at all-guides.com
Care for main body
● Wipe off the toner/moisturizing product on the head and the body with a tissue.
When dirt is difficult to remove, wipe it off with a cloth after saturating it with water and
wring it thoroughly.
Do not clean the main body with water. Or do not dip in water,
and do not pour water. (Cause of failure)
Make sure to turn OFF the switch. (Improperly turning on the switch
may give a tingling sensation or result in malfunction or short-circuit.)
★Do not use alcohol, benzine, or thinner.
CAUTION
(Cause of deformation or discoloration)
This mark means that this appliance shall not be used near water contained
in bath-tubs, basins or other vessels.
How to preserve
Store the device on the included stand in a place free from excessive humidity or dirt.
The stand can store the rings in it as well as put the body on it. (Fig. 12)
Do not leave in a water splashing area or an area with significant
humidity, such as a bath. (Cause of short-circuits or failure)
★Do not leave in an area subject to direct sunlight (inside of a vehicle in
CAUTION
summer, etc.) or near heaters. (Cause of deformation or discoloration)
Specifications
Power adaptor
100 - 240V AC, common to 50-60Hz
Power
(KH-182B)
supply
Main body Batteries [Nickel-hydrogen battery (1.2V DC, 500mAh×2)]
Charging time
5 hours as standard
Rated time Around 15 minutes at the maximum
(basic mode:approximate 10 minutes)
Accessories Rings (two), stand

Disposal of the product

Do not disassemble except when disposing of the product.
This product includes recyclable parts.
The battery is to be disposed of safely.
For disposal of the parts, observe your local laws and regulations etc.
How to remove the nickel-hydrogen batteries
Remove the battery before disposing of the main body.
1. Disconnect the power adaptor from the main body when removing the battery.
2. Keep pressing the power switch continuously while it is "ON" for about 10 seconds or
more to make the device vibrate and leave it until the vibration stops.
3. With the switch at "OFF", remove the two screws on the reverse side of the main body.
(Fig. 13) Screws
4. Insert a flat-blade screwdriver or the like in the gap between the main body cases (front)
and (rear), and remove the main body case (rear). (Fig. 14)
Flat-blade screwdriver Main body case (rear)
-12-