Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
H-5784
FLOOR SAFE
TOOLS NEEDED
Drill
Phillips Screwdriver
HARDWARE INCLUDED
70 mm Lag Screw x 2
Washer x 2
IMPORTANT! Record the serial number from the
tag on the back of the safe or from the tag on
the front bottom corner of the safe.
Keep keys and combination in a secure place,
away from children.
Do not store the backup key, combination or
this document in the safe.
WARNING! Keep safe closed and locked at
all times when not in use. Children could
accidentally be locked inside the safe.
Do not move this safe using its handle. The
handle should only be used for opening and
closing the door of the safe.
Do not store electronic media, computer disks,
audio-visual media or photographic negatives
in this safe. This material will not survive the
rated internal temperature of the safe. This
material may be damaged or destroyed.
BATTERY INSTALLATION
1.
User must first install the battery, which is located in
the front protective styrofoam.
NOTE: When changing the battery, always
hold the battery connecting cap while
disconnecting or attaching the battery. Do not
pull on the wires. Doing this could cause the
power supply to become disconnected from
the lock.
2. This safe uses one 9V alkaline battery.
PAGE 1 OF 9
1-800-295-5510
uline.com
17 mm Wrench
7/16" Drill Bit
40 mm Plastic Anchor x 2
USAGE
3/8" Drill Bit
3. When the battery is low and button is pressed on the
keypad, a red light will come on warning that the
battery is low.
4. To replace the battery, remove the cover by pressing
the tab and turning the cover. (See Figure 1)
Figure 1
5. Replace the old battery and screw the cover back
in place.
ELECTRONIC LOCK
1. After installing the battery, to open an electronic
lock the first time, press the following numbers/
symbols on the electronic keypad in this order:
1-5-9-#. These numbers are preset.
NOTE: Change the entry code as soon as
possible after opening the safe to ensure
proper security.
2. After entering the factory code, turn the handle
clockwise to open the door. User will have five
seconds to turn the handle before the locking
mechanism is reactivated.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
1020 IH-5784
Tabla de contenido
Manuales relacionados para Uline H-5784
Resumen de contenidos para Uline H-5784
- Página 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-5784 1-800-295-5510 uline.com FLOOR SAFE TOOLS NEEDED Drill Phillips Screwdriver 17 mm Wrench 7/16" Drill Bit 3/8" Drill Bit HARDWARE INCLUDED 70 mm Lag Screw x 2 Washer x 2...
-
Página 2: Entering Your Security Code
CAUTION! The safe must be secured to the HAS BEEN ENTERED CORRECTLY. floor. Use the hardware provided or consult Uline Customer Service at 1-800-295-5510 4. If the code fails, go through steps 1-3 again. If the for fastening hardware for your particular code works successfully, record combination in a mounting surfaces. - Página 3 3. Keep the door open until you have entered a new security code. Before entering new code, remove the key and screw the cover back in place. 4. Enter new security code following the instructions on page 2. 1-800-295-5510 uline.com PAGE 3 OF 9 1020 IH-5784...
- Página 4 H-5784 800-295-5510 uline.mx CAJA FUERTE DE PISO HERRAMIENTAS NECESARIAS Taladro Desarmador de Cruz Llave de 17 mm Broca de 7/16" Broca de 3/8" TORNILLERÍA INCLUIDA 2 Tornillos Tirafondo de 70 mm 2 Rondanas 2 Anclajes de Plástico de 40 mm ¡IMPORTANTE! Anote el número de serie de...
-
Página 5: Continuación De Uso
¡PRECAUCIÓN! La caja fuerte se debe fijar al los pasadores se retraigan. piso. Utilice la tornillería incluida o consulte a Servicio a Clientes de Uline al 800-295-5510 NOTA: NO cierre la puerta hasta confirmar sobre la tornillería de fijación apropiada para que el nuevo código de seguridad se ingresó... - Página 6 Antes de ingresar un nuevo código, retire la llave y atornille la cubierta en su lugar. 4. Ingrese su nuevo código de seguridad siguiendo las instrucciones de la página 5. 800-295-5510 uline.mx PAGE 6 OF 9 1020 IH-5784...
-
Página 7: Outils Requis
H-5784 1-800-295-5510 uline.ca COFFRE-FORT DE PLANCHER OUTILS REQUIS Perceuse Tournevis cruciforme Clé de 17 mm Mèche de perceuse Mèche de perceuse de 7/16 po de 3/8 po MATÉRIEL D'INSTALLATION INCLUS Tirefond de 70 mm x 2 Rondelle x 2 Ancrage en plastique de 40 mm x 2 UTILISATION IMPORTANT! Notez le numéro de série figurant... -
Página 8: Choisir L'emplacement
Service à la clientèle permettant ainsi de la tourner et de faire rentrer les de Uline au 1 800 295-5510 pour obtenir le pênes. matériel de fixation d'après le type de surfaces spécifique à... -
Página 9: Clé De Secours
Avant d'entrer votre nouveau code de sécurité, retirez la clé et revissez le couvercle à sa place. 4. Entrez votre nouveau code de sécurité en suivant les instructions à la page 8. 1-800-295-5510 uline.ca PAGE 9 OF 9 1020 IH-5784...