Denver TRC-1470 Manual De Instrucciones página 2

and hold 2 seconds to clear both IN/OUT temperature memory.
D. [+] & [-] button
Press the [-] side to decrease the setting when enter setting mode of clock, alarm or temperature alert.
When display the alarm time, press [-] side to turn Daily Alarm on/off.
When display the temperature alert, press [-] side to turn the corresponding temperature alert on/off.
Press the [+] side to increase the setting when enter setting mode of clock, alarm or temperature alert.
E. [CHANNEL] button
Toggle to display remote thermo channel from channel 1, channel 2, channel 3 to Auto-scroll mode which alternately
display 3 channels;
Press and hold 2 seconds to activate searching mode for remote sensor;
Remote Sensor
The remote sensor has 3 function buttons inside the battery compartment.
a. [CH] button
After the battery installation, the LED blinks slowly every 1.5 seconds and channel number shows '1' to indicate it is now
under channel setting mode and is set to channel 1 by default. If the user presses no key within ten seconds, the unit
will auto-exit the channel setting.
If the user press [CH] button once during the channel setting, the channel number is changed to '2' to indicate the unit
is set to channel 2. If the user press [CH] button again, the channel number will be advanced to channel '3' and so on.
Note: Never set the channel to '4' & '5' which would not be applied in this model
b. [C/F] button (for sensor with LCD)
Press to toggle unit °C or °F
c. [RESET] button
Press to hardware reset the unit to factory setting
3. BATTERY INSTALLATION (Batteries NOT included)
NOTE: Please insert batteries for the main unit first, then the RF remote sensor.
BATTERY INSTALLATION FOR MAIN UNIT
a. Remove the battery door;
b. Insert 2 pieces AAA size 1.5V alkaline battery as indicate by the polarity;
c. Close the battery door.
BATTERY INSTALLATION FOR REMOTE SENSOR UNIT
a. Lift off the bracket stand of the remote sensor unit by releasing the 2 fixing snaps at the bottom;
b. Use a small Philips type screwdriver to remove the battery cover screws;
c. Insert 2 pieces of AAA size batteries according to the "+" and "-" polarity marks shown in the battery compartment and
then close the battery door.
WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE
a. Insert x2 AAA batteries first to the main unit. The temperature display shows '—.-C' while the wave icon will keep
blinking for 2 minutes indicate the main unit is in sensor searching mode.
b. In a second step, insert the x2 AAA batteries into the sensor unit. The LED on the front panel will start flashing at a rate
of one time per around 2 seconds indicates channel-1 is in use.
c. While the LED is flashing, press once the [CH] key will change the sensor channel setting to 2. Keep toggle on [CH] key
can change channel setting up to 3. The LED is blinking at a frequency to indicate the channel setting. i.e. continuous
blinks 2 times indicate channel-2 is selected.
Note: If user does not press any key for 10 seconds, it will exit the channel setting mode and transmit the RF signal.
The main unit will register the temperature reading.
4 . HOW TO SET TIME AND CALENDAR
a. Make sure the 1 line of the LCD displays the clock time, press & hold [CLOCK] button for 2 seconds to enter clock setting
st
mode. Flashing 24 hours will appear.
b. Press [ + ] or [ - ] button to switch between 24 hours and 12 hours format, and then press [CLOCK] button to confirm.
c. The hour digits will flash. Use the [ + ] button to increase by one hour or [ - ] button to decrease by one hour to your
desired hours. Holding down either button will change the increment rapidly. Press [CLOCK] button to confirm.
d. The minute digits will flash. Use the [ + ] button or [ - ] button to set your desired minutes. Holding down either button
will change the increment rapidly. Press [CLOCK] button to confirm.
Note: Every change of minute digit will automatically reset the seconds to zero.
e. The year digit will flash and Yr icon appears. Press [ + ] or [ - ] button to set your desired year. Press [CLOCK] button to confirm.
Note: Year range is from 2000 to 2099.
f. D and M icons will flash. Press [ + ] or [ - ] to select D M (Date Month) or M D (Month Date) format. Press [CLOCK]
button to confirm.
ENG
All manuals and user guides at all-guides.com
~P.2~