Electrical Connection; Illustrated Description; Operating Instructions; Placement And Testing - stayer VAC1200 Manual Del Usuario

Mounting the Vacuum Hose
Insert the vacuum hose 6 into the hose connection piece 7
until it is locked. Insert the extension tubes firmly into each
other 14.

3.3 Electrical connection

Observe the correct mains voltage! The voltage of
Ÿ
the power source must agree with the voltage
specified on the nameplate of the vacuum cleaner.
Vacuum cleaners marked with 220–240 V can also
be connected to 220 V
Switch the vacuum cleaner off immediately as soon
Ÿ
as foam or water comes out, and empty the
container. Otherwise, the vacuum cleaner can
become damaged.
Switching On and Off
To start the vacuum cleaner, set the On/Off switch 9 to
position "I".
To switch off the vacuum cleaner, set the On/Off switch 9 to
position "0".

3.4 Illustrated description

1 Wheels
2 Carrying handle
3 Base vacuum cleaner
4 Latch of the vacuum cover
5 Container
6 Vacuum hose1.5 m - Ø30mm
7 Release button for hose connection piece
8 Hose connection piece
9 On/Off switch
10 Vacuum lid
11 Permanent filter
12 Float
13 Dust bag (5unid)
14 Adjustable handle or tube
15 Pre-filter
16 Tube plate
17 Brush

4.Operating instructions

4.1 Placement and testing

CAUTION! This appliance is not suitable for picking up
hazardous dust. Do not vacuum inflammable or
explosive fluids; for example, benzene, oil, alcohol,
solvents. Do not vacuum hot or burning dust. Do not
operate the machine in rooms where the danger of an
explosion exists. The dusts, vapours or fluids can ignite or
explode.
The vacuum cleaner may not be used as a water
Ÿ
pump. The vacuum cleaner is intended for vacuuming
air and water mixtures.
Before any work on the vacuum cleaner itself, pull
Ÿ
the mains plug.
All manuals and user guides at all-guides.com
ENGLISH
8
Note: Before wet vacuuming, the dust bag 13 must be
removed and the container 5 must be emptied.
The vacuum cleaner is equipped with a float 12. When the
maximum filling height is reached, the vacuum cleaner
switches off. Set the On/Off switch 9 to position "0" and
empty the container 5.
After vacuuming, prevent the forming of mould and allow it
to dry thoroughly; especially before using it for dry
vacuuming.

4.2 Adjustment operation

Removing the Vacuum Hose
To remove the suction hose 6 push while turning as directed
(arrow) and pull out the suction hose 6.
Removing/Replacing the Permanent Filter
To maintain the optimum performance of the vacuum
cleaner, clean the permanent filter 11 by brushing off or
rinsing with water after each use.

4.3 Correction of Malfunctions

In the case of insufficient vacuuming performance, check
the following:
– Is the vacuum lid 10 attached properly?
– Is the hose system clogged?
– Are the extension tubes connected firmly?
– Is the container 5 full?
– Is the dust bag 14 full?
– Is the permanent filter 11 clogged with dust?
Emptying at regular intervals ensures optimum vacuuming
performance.
If the vacuuming performance is not achieved thereafter,
take the vacuum cleaner to customer service.

5.Maintenance and service instructions

Before any work on the vacuum cleaner itself, pull the
mains plug.
For safe and proper working, always keep the vacuum
cleaner and ventilation slots clean.

5.1 Cleaning

If the replacement of the supply cord is necessary, this has
to be done by STAYER or an authorized STAYER service
agent in order to avoid a safety hazard.
Container
Wipe out the container 5 from time to time with a
commercially available, non-scouring cleaning agent and
allow to dry.
8