Internal Cleaning - FrostEmily PRISMA 200 TN Instalación Y Uso

Operator's guide:
1. Unpacking instructions
2. The handle
3. Internal grids
I

4. Internal cleaning

5. Connection to the mains
UK
6. Controls
7. Checking correct operation
D
8. Internal cleaning
E
!
WARNINGS (see figure 10)
It is most important that this instruction booklet is kept together with the appliance both for future
F
reference and for reasons of safety.
1
. Adults should operate this appliance only. Do not allow children to use the controls or play with it. . It
NL
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
4. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
P
5
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
6
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. . The
S
manufacturers of this appliance accept no responsibility for the consequences of misuse in contravention
of these safety instructions. It further reserves the right to carry out improvements without prior notice.
DK
8
. Avoid installing the cabinet directly in line with sunlight. . Never install the appliance near sources of
heat (such as radiators, stoves, etc) and drafts (such as windows, doors, ventilation systems, air
FIN
conditioning, etc ...).
the products displayed on the shelves and grills do not hang over the edges.
B
to be refrigerated should cause ice to form on the evaporator, we recommend stopping the compressor
and placing the goods in special refrigerated containers, kept at the same temperature, until defrosting is
GR
completed;if this is not carried out the compressor will continue to operate leading to a wasteful
consumption of electricity and poor performance.
indispensable to keep the door open at least 10 cm.
CZ
EE
!
Our products are for internal use only – do not install outside restaurants, shops.
LV
1. UNPACKING INSTRUCTIONS
LT
CARDBOARD PACKAGE 1a
Remove the nails from the wooden crate with care.
H
and pallet or crate.
and level surface.
M
packaging materials to facilitate disposal (see figure 1).
2. THE HANDLE
PL
1.
The handle can be found in a bag inside the appliance.
the two screws already inserted in the holes. Tighten with care.
SK
and press down until it clicks into place (see figure 2).
SLO
3. INTERNAL GRIDS
1.
The grids can be found at the bottom of the cabinet.
height-adjustable supports (see figure 3).
4. INTERNAL CLEANING
1.
Clean the inside with a soft cloth and neutral detergents.
cleaning : 1. Use the same products as used for the internal cleaning.
5. CONNECTION TO THE MAINS
1. Ensure that mains voltage and frequency are the same as those stated on the rating plate (A) attached
to the appliance.
earthed. b)
with the IEC regulations: - magnetothermal differential switch (also known as ground fault interrupter)
with In = nominal value as stated on the rating plate; - Differential with Id sensitivity = 30 mA. 3. Ensure
that there is no danger of explosion (AD) in the room. . The connecting cable to the appliance is H05
VVF, designed for internal use. For installation in any other environments, it will be necessary to change
the cable with the appropriate type (for example H07 VVF for external use).
use three-way adapters and reduction adapters).
been placed by mistake in a horizontal position or has been turned upside down, leave for at least three
hours in the correct position before switching on the power supply (see figure 4).
10
. Keep the ventilation grills free from obstruction for at least 30 cm.
Cut the strap and lift up the cardboard package.
3.
Lift the appliance. . Remove the pallet or crate.
6.
Make sure there is nothing left in the package before disposal.
2.
Ensure that the supply socket has the following characteristics:
It fulfils the requirements of the rated current as set out on the rating plate.
Operator's guide
9. Replacing the internal lights
10. Replacing the door's magnetic gasket
Maintenance manual (Page 48):
1. Cleaning the condenser
2. Replacing a glass panel
3. Wiring diagram diagram of refrigeration unit
9
13
. If the appliance is not working and unused, it is
2.
Insert the forks of a forklift truck between appliance
4
2
. Fix the handle base to the door frame using
3.
2.
Assemble the grids by fitting them into the
2.
Dry with a soft cloth.
4
N.B.
If during transport or storage the appliance has
6
3
11
12
. If damp air or products
WOODEN CRATE 1b
5.
Place the appliance on a flat
7.
Separate the
Place the plastic insert over the handle
External
a) it is properly
c) It complies
5
. Connect the plug (do not
2
7
.Ensure that