General Operation - Aeg Bss 4811 Instrucciones De Servicio

English
40
Remote Control
1 POWER/STANDBY button (On/Off)
2 RANDOM button (random playback)
3 PLAY/PAUSE (play/pause / auto scan /manual search)
button
4 − MEMORY / FOLD. +/10 buttons (select memory loca-
tion/album)
5 REPEAT (repeat) button
6 EQ button (Equalizer)
8 MUTE button
7 VOL+/VOL- buttons (volume)
9 MEMORY/PROGRAM button (memory)
10 F-SKIP/ / UP / B-SKIP / DOWN buttons (next/previous
track)
11 button (stop)
12 PAIR / MO/ST button (Bluetooth pairing / switching
between mono/stereo modes)
13 FUNCTION button (select source)
First Use of the Device/Introduction
NOTE:
The device is operated primarily with the remote control.
Thus the descriptions refer to the buttons on the remote
control. Some buttons are also on the device. Buttons with
the same name have the same function.
• Select a proper place for the device. A dry, level and slip
proof surface is suitable.
• Make sure the device is vented sufficiently!
• Remove the protective film from the device, if present.
Power supply
• Insert the grid plug into a properly installed three prong
socket with 230 V, 50 Hz. Connect the device with the
plug connector by inserting its plug into the DC IN jack of
the device.
• Make sure the grid voltage corresponds to the figures on
the rating plate.
CAUTION:
• The included AC adapter may only be used with this
device. Do not use it for other devices.
• Use only an AC adapter with DC IN 12 V (
different AC adapter may damage the unit.
NOTE:
Disconnect from mains power supply during longer periods
of non-use.
Insert/Replace Battery in Remote Control
• Open the battery compartment on the underside of the
remote.
• Insert AAA/R03 1.5 V type batteries. Pay attention to the
correct polarity (see bottom of battery compartment)!
• Close the battery compartment.
If the remote is not in use for a lengthy period of time, please
remove the battery to prevent the battery acid from "leaking".
WARNING:
• Do not expose the batteries to intense heat, such as
sunlight, fire or similar. Danger of explosion!
• Keep batteries out of the reach of children. They are
not toys.
• Do not force batteries open.
• Avoid contact with metallic objects. (Rings, nails, screws
etc.) Danger of short circuits!
• Short circuits may overheat or even ignite batteries.
This may lead to combustion.
• When transporting the batteries, cover the terminals for
your safety with an adhesive strip.
• If a battery leaks, do not rub the fluid into the eyes or
the skin. If acid comes into contact with the eyes, rinse
with purified water and seek medical advice if symp- toms persist.
CAUTION:
• Different battery types or new and used batteries may
not be used together.
• Batteries must not be disposed of in the garbage.
Please bring used batteries to competent collection
centers or back to the dealer.

General Operation

Switch device on/off
• With the button (1), you can switch the unit between
standby and operating mode. During standby, the indica-
tor lamp of the STANDBY/FUNCTION button (1 on the
device) lights up.
• To disconnect the unit completely from the mains, pull
the mains plug from the socket.
NOTE:
• Press and hold the STANDBY/FUNCTION button (1)
on the device in order to switch between standby and
operating mode.
• After about 15 minutes without signal, the device will
automatically switch to Standby.
). A
Volume
By pressing the VOL+/VOL- buttons (2/7) you can adjust the
desired volume.
Infrared Remote Control
For wireless control within a distance of 5 m. If the distance
decreases you should change the batteries. For proper
operation mind a clear view between the remote control and
the sensor on the device.