Idiomas disponibles
Idiomas disponibles
LAP COUNTER - CHRONOGRAPH
KEYS and FUNCTIONS:
- Laps programation: (P-LA): maximum 9999 laps, minimum
1 lap.
- F-1 programation: (P-F1): maximum 9999 laps, minimum 1
lap.
- Minimum time gap between laps: (Pt): See advanced
programation.
When push of this key, the digit will start blinking on lane 2,
one after the other after each push of this key, you always can
modify (with the key 0-9) the one is blinking to obtain the
programmation needed.
If there is no key push during 3 second, the blinking stops
and shall be pressed the key again, leaving the actual view as
the programmed one (not in memory) only during the following
race.
Allows to grow up the numbers on the blinking digit while
the progamm "0000" is actived.
This key also activate and disactivate the sound (beep)
system. This function works always when no programming
functions is actived.
PAUSE (memory)
During programming (blinking) this key works as a
key, when the programmation is done and while the numbers
are still blinking, if you push this key the actual programm is
saved in permanent memory. This allow to disconect the lap
counter and connect it again without the need to programm
again.
- During the race this key works as a pause key, stopping
the system to count laps and if the "stop and go box" (Ds.21) or
"PRO Stop and go
box" (DS.61) are connected also stopps the
cars it the same moment when the key is pushed. There is a
beep signal during the first 20 seconds of the pause. A second
push of this key continue again the race, giving power to the
track and continue the lap counter with the same data as before
the pause stop.
- Allow to programm the race in
advanced programmation.
ADVANCED PROGRAMMATION:
Programming gap time between laps
You can use this key for 2 main functions:
- Programming a minimum time gap, you can avoid false lap
counting to other lanes (because of lane changing), then is
only needed to programm "pt" to a little less than the fastest
lap in the circuit.
Example: If the fastest lap is 8,426 seconds, we can programm
the "pt" to 7,500 seconds then when the is a lane changing
because a car goes out of the lane and inside another lane, it
will cross infraredbrige only one time between the following
7,500 seconds. So the rafe director only have to add a lap on the
car that goes out and crosses by another lane. Also avoid that
somebody try to mark laps with the hand throught the infrared
bridge.
- It is also usefull for testing motor or cars, So programming
a minimu "Pt" (like 0,05 seconds) and setting up a doble
sensor in the middle of the straight separated for example
1 meter between them, when you run between the sensors,
you have a fast lap (time between the 2 sensors) so pushing
Chronos key you will have a time , that you can compare
with other cars/motors, knowing then which is the faster
car/engine.
- With this time record you can sort out the real speed of the
model when passing under the sensors (Speed: meter/
seconds). (You need to buy a "V" wire (ref. DS.18) to connect
doble sensor.)
•
Programming especial control
racing.
TOTAL
Control: Indicates that the computer will stop / start
all cars at the same time, something usuall in Slot racing
competition.
2
0000
key:
0—9
key:
key:
"time
on" or
"time
off". See
"Pt"
TOTAL / INDIVIDUAL
OPERATION MANUAL
DS - 300 "PRO SERIES"
INDIVIDUAL
start the cars one by one when they finish the programmated
mode. This is a must programm to use the new features Formula1,
as at the end of the race , the winning car stops and in the
following lap the rest of the cars stops when they cross the
sensor, knowing the rest of race places because of lap difference
and time spend on the last lap.
It is also usefull to do racing to a determinate laps and know
the time spend on
It is needed that all cars finish the race to know all timing. Only
pushing the LAPS/TIME key we will know all time spend on all
lanes.
For
INDIVIDUAL
STOP and GO
Programming:
- Must disconnect the power from the lap counter.
- Keep the key "pause / memory" pushed while the power
is connected to the lap counter (12V), you will see on display
lane1 "CtrL" (control) and on lane2 display "ttAL" (total)
- Leaving the "pause/memory" key, push the key "MODE",
the lane2 display will switch from "ttAL" (total) to "Indi"
(Individual), leave the one you need
- Press the "Pause/memory" key to validate the
memory
programmation.
This mode will keep permanent in memory, untill new change.
•
Programming
With
"time
time when the green light is on and activate the relee "STOP
and GO" box (DS.21) or
power to the track, so all cars will start at the same time.
With
"time
showed with a blinking "----" in the displays. After it the red light
is on for few seconds (NOT COUNTING laps if crosses, and if
it is the driver gets penalized with the complete lap). When red
light is over will start counting time when a car cross for first
time the sensor, starting to count the fist lap at the first cross.
This new start is a system not used before but that gives a real
free start on the races.
This system is normally used for Rally-slot with lap
programmation. With the advantage that the cars (using "stop
& go box" or
of the race.
Programming:
- Keep pushed the
and then on lane1 display shows "Ti" (time and on lane2
display shows "on".
- Leaving the "pause/memory" key, push the key "MODE",
the lane2 display will switch from "on" to "off", leave the
one you need.
- Press the "Pause/memory" key to validate the progammation.
This mode will keep permanent in memory, untill new change.
ALL DIFFERENT PRORAMMS YOU CAN DO
used program MODES:
Racing mode:
Rallye-Slot racing
Hillclimbing
Endurance or speed racing Programm #5 or #7
Formula 1 style
Comercial or rental use
on
Control: Indicates that the computer will Stop/
each car
to cover the full programmed laps.
control is needed to have the new
box" (DS.0061)
"time
on" and
"time
off"
on" the lap counter will start counting the race
"PRO-Stop and
Go" box (DS.61) giving
off" the lap counter give power to the track
"pro Stop &go
box") will always stop at the end
"pause/
memory" key during 4 seconds
Programm number
Programm #4
Programm #2 or #4
Programm #10 or #12
Programm #2 or #10
"PRO-
Mostly
Optional accessories
"Stop and Go box"
(1 relee)
"Pro Stop and Go
box"
(2 relee)
"Pro Stop and Go
box"
(2 relee)
"Pro Stop and Go
box"
(2 relee)
"Pro Stop and Go
box"
(2 relee)
