Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Cycle Adjustments
A suitable drying temperature and dryness level
will automatically be displayed for the cycle se-
lected. To change the settings, press TEMPS and
DRYNESS until the desired selections are made.
These adjustments to the cycle will automatically
be remembered each time that cycle is selected.
Temperature Selection
For best results, follow the fabric care label
instructions on items to be dried. Select the tem-
perature setting most suitable for each load.
To avoid fire hazard, do not use heat
to dry items containing feathers or down, foam
rubber, plastics, or similarly textured, rubber-like
materials. Use the Air Fluff-No Heat cycle only.
High is recommended for sturdy fabrics.
Medium is recommended for wrinkle free, per-
manent press and lightweight fabrics.
Medium-Low is recommended for most knits.
Low is recommended for delicate fabrics.
Note: To prevent shrinkage, every temperature is
not available with every cycle.
Dryness Selection
Select Normal Dry for most loads.
Occasionally a load may seem too damp or over-
dried at the end of the cycle. To increase drying
time for similar loads in the future, select More
Dry. For loads requiring less drying time, select
Less Dry.
Select Damp Dry for items you wish to partially
dry before hanging or ironing. Select the tempera-
ture most suitable for the load.
Page 2
All manuals and user guides at all-guides.com
Note: To prevent over-drying, every dryness level
is not available with every cycle.
Cycle Options
Press Saver
If the dried load cannot be removed promptly at
the end of the cycle, unheated tumbling continues
for approximately 30 minutes to help reduce wrin-
kling. When the signal is selected, it will beep briefly
approximately every 4 minutes as a reminder to
remove the load. The dried load can be removed
at any time during Press Saver.
No Heat
This option provides up to 30 minutes of tumbling
without heat and can only be selected in the Timed
Dry cycle. Use it to dry items containing feathers
or down, foam rubber, plastics or similarly textured,
rubber-like materials, to freshen clothing, pillows
or blankets, or to dust draperies.
Dryer Features
Control Lock
To prevent accidental operation of the dryer or al-
teration of the cycle settings, press and hold the
lock symbol until you hear 3 beeps and "LOC" is
displayed. To cancel, press and hold the lock sym-
bol until "LOC" is no longer displayed.
Signal
A signal will sound at the end of the cycle and pe-
riodically during Press Saver. Press the signal sym-
bol to select one of three volume levels or turn off
the signal. This selection will be programmed until
you change it.
Timed Dry
Use this feature to manually select the drying time
for any load. Select the temperature desired. You
will not be able to select a cycle or dryness level.
NOTE: Timed Dry is required when using the No
Heat option.
Press Timed Dry to select 45 minutes of drying
time. The time will increase 5 minutes each time
Timed Dry is pressed. The maximum drying time
is approximately 110 minutes. If you desire less
than 45 minutes, you must advance beyond the
the 110 minute mark to start again at 15 minutes.
Error Codes
If the dryer stops and the F 01, F 03, F 04 or F 05
error code is flashing in the display, press STOP/
CANCEL, select a cycle and press START. If the
error code appears again, call for service to cor-
rect the problem.
•
F 01 - There may be an internal problem
with the dryer.
•
F 02 - There may be a problem with the
temperature sensor.
•
F 03 - There may be a problem with the
heater system.
•
F 04 - The dryer may have run too long.
Clean the lint filter and be sure the
vent is not blocked before calling
for service.
•
F 05 - There may be a problem with the
keypad.
PN 134306100A 0311)
Tabla de contenido
