G
H
D
C
B
A
25w Alexander Floor Lamp
25C91HBK
25C91NKK
INS140113
REV042414
ENGLISH
CONGRATULATIONS!
You've purchased the finest in
natural lighting technology with
E
your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed
F
Product Registration Form and
return it today by mail, or
register online by going to:
www.OttLite.com/warranty.
WARNING: To prevent electric
shock, make sure the lamp is not
plugged in until all assembly steps
are complete.
LAMP ASSEMBLY
1. Make sure that the lamp is not
plugged into an electrical outlet.
2. Thread pole (B) to base (A)
turning clockwise by hand until tight.
Pull excess cord from bottom of
base (A) as needed.
3. Thread pole (C) to pole (B)
turning clockwise by hand until tight.
4. Thread pole (D) to pole (C)
turning clockwise by hand until tight.
5. Thread Shade Assembly (E) to
pole (D) turning clockwise by hand
until tight.
6. Install bulb. See BULB
INSERTION/ REMOVAL instructions.
7. Plug the lamp into a standard
120V outlet.
8. Position the shade as desired by
flexing the neck.
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
Alexander Floor Lamp
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
9. To turn lamp on or off, depress
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
rocker switch at rear of socket
assembly (F).
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF
THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
BULB INSERTION/REPLACEMENT
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED. DO
1. Make sure the lamp is not
NOT ALTER THE PLUG.
plugged into an electrical socket.
CAUTION:
2. If the lamp has been in use, allow
it to cool for approximately five
minutes before proceeding.
3. To install a bulb in the socket,
hold the bulb (H) firmly near the
base, align bulb pins with matching
pin-holes then push it straight into
¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
the socket until it "snaps" into place.
IMPORTANTES:
4. To remove a bulb (H) already
installed in the lamp, grasp it firmly
ES MÁS ANCHA QUE LA OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA.
at the base and, using a slight
ESTE ENCHUFE ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE
rocking motion, pull it straight out
of the socket. Do not twist or turn
NO CALZA COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN
the bulb.
CONTACTO CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE
PUEDA SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.
Please note that in operation,
PRECAUCIÓN:
OttLite
®
bulbs are not dimmable.
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
Enjoy your OttLite
Alexander
®
Floor Lamp!
This lighting system is designed
for use with OttLite
®
type
bulbs
(style number SB25-P). Use of
other products voids the warranty
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
and may result in damage to the
lighting system.
SÉCURITÉ:
QUE L'AUTRE). CE DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE
NE S'INSÈRE DANS LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF
SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE