English - Wurth Master EWS 115 Instrucciones De Servicio

All manuals and user guides at all-guides.com
OBJ_BUCH-413-004.book Page 14 Thursday, June 26, 2008 9:08 AM
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious
injury.
❏ See data sheet for further safety warnings
and instructions.
Safety Warnings common for Grind-
ing, Sanding, Wire Brushing or
Abrasive Cutting Off Operations
❏ This power tool is intended to function as
a grinder, sander, wire brush or cut-off
tool. Read all safety warnings, instruc-
tions, illustrations and specifications pro-
vided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
❏ This power tool is not recommended for
polishing. Operations for which the power tool
was not designed may create a hazard and cause
personal injury.
❏ Do not use accessories which are not spe-
cifically designed and recommended by
the tool manufacturer. Just because the
accessory can be attached to your power tool, it
does not assure safe operation.
❏ The rated speed of the accessory must be
at least equal to the maximum speed
marked on the power tool. Accessories run-
ning faster than their rated speed can break and
fly apart.
❏ The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
❏ The arbor size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbor holes that do not match the mounting
hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of
control.
❏ Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position your-
14–English
For Your Safety
self and bystanders away from the plane
of the rotating accessory and run the
power tool at maximum no-load speed for
one minute. Damaged accessories will nor-
mally break apart during this test time.
❏ Wear personal protective
Depending on application,
shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris gener-
ated by various operations. The dust mask or res-
pirator must be capable of filtrating particles
generated by your operation. Prolonged expo-
sure to high intensity noise may cause hearing
loss.
❏ Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury
beyond immediate area of operation.
❏ Hold power tool by insulated gripping
surfaces only, when performing an opera-
tion where the cutting accessory may con-
tact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
shock the operator.
❏ Position the cord clear of the spinning
accessory. If you lose control of the power tool,
the cord may be cut or snagged and your hand
or arm may be pulled into the spinning acces-
sory.
❏ Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.
❏ Do not run the power tool while carrying it
at your side. Accidental contact with the spin-
ning accessory could snag your clothing, pulling
the accessory into your body.
❏ Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside the
housing and excessive accumulation of pow-
dered metal may cause electrical hazards.
❏ Do not operate the power tool near flam-
mable materials. Sparks could ignite these
materials.
❏ Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
equipment.
use face
26.6.08