Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Before Using the Unit
Thank you for choosing TEAC. Read this
manual carefully to get the best
performance from this unit.
< As the unit may become warm during
operation, always leave sufficient space
around the unit for ventilation.
< The voltage supplied to the unit should
match the voltage as printed on the rear
panel. If you are in any doubt regarding
this matter, consult an electrician.
< Choose the installation location of your
unit carefully. Avoid placing it in direct
sunlight or close to a source of heat. Also
avoid locations subject to vibrations and
excessive dust, heat, cold or moisture.
< Do not place the unit on an amplifier/
receiver.
< Do not open the cabinet as this might
result in damage to the circuitry or
electrical shock. If a foreign object should
get into the unit, contact your dealer or
service company.
< When removing the power plug from the
wall outlet, always pull directly on the
plug, never yank the cord.
< Do not attempt to clean the unit with
chemical solvents as this might damage
the finish. Use a clean, dry cloth.
< Keep this manual in a safe place for
future reference.
4
All manuals and user guides at all-guides.com
Maintenance
If the surface of the unit gets dirty, wipe
with a soft cloth or use a diluted mild
liquid soap. Be sure to remove any excess
liquid completely. Do not use thinner,
benzine or alcohol as they may damage
the surface of the unit. Allow the surface
of the unit to dry completely before
using.
CAUTION
Ensure this product is not exposed to
dripping or splashing and that no object
filled with liquids, such as vases, is placed
on the product.
Do not install this equipment in a confined
space such as a book case or similar unit.
Allow adequate air circulation around this
product.
For European customers
Disposal of your old appliance
1. When this crossed-out
wheeled bin symbol is
attached to a product it
means the product is
covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the
municipal waste stream via designated
collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance
will help prevent potential negative
consequences for the environment and
human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased
the product.
Rechargeable Batteries
The R-2 uses a Nickel-Metal-Hydride battery
pack stored in the battery compartment.
Leaving the AC adaptor connected to the R-
2 and plugged into an AC line, even when
not in use, ensures the batteries will be fully
charged when you need to use the R-2 on
battery power. The R-2 can be used for 6 to
7 hours after batteries are fully charged.
< When the batteries need to be recharged,
the STANDBY/ON indicator blinks at
regular intervals. The blinking interval will
grow faster as the batteries get closer to
discharge until the R-2 shuts off
automatically to protect the batteries.
< When the R-2 is not being used but the
AC adaptor is plugged in, the batteries
will be completely charged within
approximately 3.5 hours from a full
discharge. During this period the
STANDBY/ON indicator will flash.
< When the R-2 is ON and the AC adaptor
plugged in, the batteries will be
completely charged within approximately
24 hours.
< It may take up to 4 charge and discharge
cycles before the batteries are operating
at full capacity when the R-2 is new or
left unused for several weeks.
It is suggested that the R-2 be plugged in
for about 12 hours before you use it for
the first time.
< Once the R-2 has been fully charged
while it is STANDBY, do not unplug the
AC adaptor and then immediately plug it
again. This will restart the charging cycle
even though the batteries are fully
charged. Doing this repeatedly will
damage the batteries.
< If the R-2 is not plugged in, the batteries
will slowly discharge as a safety measure.
Battery Replacement
When the batteries are exhausted, replace
the battery pack with a new one.
1. Remove the battery compartment cover.
2. Disconnect the battery pack connector,
and remove it.
3. Insert a new battery pack and attach its
connector.
4. Close the cover.
Caution:
< Do not heat or disassemble rechargeable
batteries. Never dispose of old batteries
by throwing them in a fire
5
Tabla de contenido
