Tabla de contenido
Idiomas disponibles
Idiomas disponibles
WARNING!
Charge only MILWAUKEE 12, 14.4
and 18 Volt battery packs in
MILWAUKEE
chargers.
Other
brands of batteries may explode
causing personal injury and dam-
age.
For specific charging instruc-
tions, please read the operator's
manual
supplied
with
your
charger.
Inserting Battery Pack into Tool
(Fig. 1 & 2)
The battery pack may feel warm after the
charging cycle. If it is warm, maximize the
output of the battery by allowing it to cool for
a few minutes before inserting it into the tool.
Battery pack can be inserted into the tool
in two ways.
Fig. 1
1.
For working in restricted spaces.
Insert the battery pack from the front
by sliding battery pack into the body of
the tool. Insert the battery pack until
the battery latches lock.
Fig. 2
2.
For optimum weight distribution and
balance.
Insert the battery pack from the back
by sliding the battery pack into the body
of the tool. Insert the battery pack until
the battery latches lock.
3.
To remove the battery pack, press in
both battery latches and slide the bat-
tery pack off of the tool.
All manuals and user guides at all-guides.com
ASSEMBLY
WARNING!
Always lock trigger or remove
battery pack before changing or
removing accessories. Only use
accessories
specifically
recommended
for
this
tool.
Others may be hazardous.
WARNING!
To reduce the risk of injury, always
use a side handle when using this
tool. Always brace or hold securely.
Installing the Side Handle
1.
To install the side handle, loosen the
side handle grip until the ring is large
enough to slide over the torque selec-
tor collar. The raised rib on the side
handle ring fits inside the groove
around the tool. Rotate the handle to
the desired position and tighten the
side handle until it is secure.
2.
To remove the side handle, loosen
the side handle grip until the ring is
large enough to slide off the tool.
8
OPERATION
WARNING!
To reduce the risk of injury, wear
safety goggles or glasses with
side shields.
Using Keyless Chucks (Fig. 3)
Your cordless tool is equipped with a spindle
lock. The chuck can be tightened with one
hand, creating higher grip strengths on the bit.
Always remove the battery pack or lock
the trigger before inserting or removing bits.
Fig. 3
Sleeve
1.
To open the chuck jaws, turn the sleeve
in the counterclockwise direction.
When using drill bits, allow the bit to
strike the bottom of the chuck. Center
the bit in the chuck jaws and lift it about
1/16" off of the bottom.
When using screwdriver bits, insert
the bit far enough for the chuck jaws
to grip the hex of the bit.
2.
To close the chuck jaws, turn the
sleeve in the clockwise direction. The
bit is secure when the chuck makes a
ratcheting sound and the sleeve can
not be rotated any further.
3.
To remove the bit, turn the sleeve in
the counterclockwise direction.
NOTE: A ratcheting sound may be heard
when the chuck is opened or closed. This
noise is part of the locking feature, and
does not indicate a problem with the chuck's
operation.
Using Clutch (Fig. 4)
This tool has an adjustable clutch for driv-
ing different types of screws into differ-
ent materials. When properly adjusted, the
clutch will slip at a preset torque to pre-
vent driving the screw too deep and to
prevent damage to the screw or tool.
To adjust the clutch, turn the torque selec-
tor collar to one of the twenty positions
shown on the collar. The number must line
up with the arrow on top of the tool.
Fig. 4
Torque selector
collar
Position numbers
The torque specifications shown here are
approximate values obtained with a fully
charged battery pack.
Selecting Speed (Fig. 5)
Fig. 5
High
L o w
The speed selector is on top of the motor
housing. Allow the tool to come to a com-
plete stop before changing speeds. See
"Applications" for recommended speeds
under various conditions.
1.
For Low speed (up to 500 RPM), push
the speed selector forward.
2.
For High speed (up to 1700 RPM), push
the speed selector back.
9
Tabla de contenido
