Resumen de contenidos para CyClone 89036080
- Página 1 OPERATING INSTRUCTIONS AND PARTS MANUAL 89143380-2 For technical assistance or the Dealer nearest you, call (360) 833-1600 8.914-338.0...
-
Página 2: Tabla De Contenido
Date of Purchase ____________________________ The model and serial numbers will be found on a decal attached to the Cyclone. You should record both serial number and date of purchase and keep in a safe place for future reference. Cyclone System Manual • Form #8.914-338.0 • Rev. 11/12... -
Página 3: Introduction
INTRODUCTION WARNING: High pressure stream WARNING of fluid that equipment can The Cyclone is designed to attach to a pressure washer produce can pierce skin and its which rotates two high pressure nozzles in the Cyclone. underlying tissues, leading to The nozzles produce spray as well as determine the size serious injury. -
Página 4: General Operating Techniques
NOTE: We recommend using no mar hose to prevent black marks from appearing on the cleaning surface. 3. Couple pressure washer high pressure hose to Cyclone. 4. Inspect your pressure washer nozzle size. The Cyclone surface cleaner comes with two #3 nozzles. -
Página 5: Alignment Tool, 8.912-854.0
STEP 2: Place base of alignment tool flat against STEP 1: Disconnect water to Cyclone, then turn bottom of Cyclone plastic body. Press end entire machine over to allow access to nozzle jets. of tool (opposite of desired angle) against axle, then rotate nozzle arm to alignment tool as shown. -
Página 6: Exploded View
CYCLONE SYSTEM OPERATOR’S MANUAL EXPLODED VIEW 89143380-1 8.914-338.0 • Rev. 11/12... -
Página 7: Parts List, Exploded View
CYCLONE SYSTEM OPERATOR’S MANUAL EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 8.706-200.0 Elbow, 1/4", Male Pipe 8.719-966.0 Adapter, Valve, Trigger Bar 8.706-560.0 Cap, Black Vinyl 8.912-851.0 Handle, Lower Assy 8.751-362.0 Base, Polyethylene, Black 8.912-852.0 Handle, Upper Assy 8.705-969.0... -
Página 8: Troubleshooting
NOZZLE CHART Correct nozzle size is important for optimum cleaning efficiency. The Cyclone is shipped with two #3, 15° nozzles in rotary swivel. Review correct nozzle size for your pressure washer. See chart below for correct nozzle size. To obtain the correct nozzle size in the rotary swivel, divide the minimum nozzle size for the pressure by two. -
Página 9: Warranty
CYCLONE SYSTEM OPERATOR’S MANUAL Cyclone System WARRANTY LIMITED MINIMUM 90 DAY WARRANTY We warrant to the original consumer that each new part and accessory sold by Kärcher North America (KNA) will be free from manufacturing defects in materials or workmanship in normal service for the duration specified by the original component manufacturer with a 90 day minimum from date of purchase, provided it is installed properly and the equipment is maintained in accordance with KNA's instructions and manuals. -
Página 10: Spanish
4. Deben usarse accesorios de seguridad para los ojos y protección de los pies cuando se use este equipo. El Sistema de Cyclone de agua está diseñado para 5. El mejor seguro contra un accidente es la precaución adaptarse a una lavadora de presión haciendo rotar dos y el conocimiento de la máquina. -
Página 11: Systema De Chorro De Agua
SYSTEMA DE CHORRO DE AGUA MANUAL DEL OPERADOR 11 NOTA: Para un lavado ideal, el Sistema de chorro de agua debe adaptarse a un lavador de un mínimo de 4 gpm y 3,000 psi de presión. 5. Prender el suministro de agua y arrancar la lavadora de presión. -
Página 12: Herramienta De Alineamiento
Tobera Herramienta de Ajuste Carrocería Plástica PASO 1: Desconecte el agua de Cyclone, luego gire PASO 2: Coloque la base de la herramienta de ajuste la máquina completa para permitir el acceso plana contra la parte inferior de la carrocería a las toberas de chorro. - Página 14 Cyclone System Form #8.914-338.0 Revised 11/12 Printed in U.S.A. • •...