MORDOMUS iMS5 Manual De Instrucciones página 2

EN
iMS5 – Multi-Sensor
Features:
• 8 infra-red outputs with 640 bits of data;
• 20 infra-red inputs with 256 bits of data;
• reads temperature;
• reads luminosity;
• Motion detection;
• Tamper protection;
• MdiBus interface;
Applications:
• Infra-red remote control interface, temperature,
luminosity and motion detection with
protection.
Specifications:
Power supply voltage: 15VDC;
Consumption: 35mA nominal @ 15VDC;
Storage temperature: -10ºC a 60ºC;
Operating temperature: 10ºC a 50ºC;
Maximum humidity: 80% non-condensing;
Temperature range: 0 to 50ºC;
Brightness: 100 levels;
Infra-red inputs: learns and recognizes up to 20 infra-red remote
control keys that can serve as Mordomus inputs;
Infra-red outputs: learns and reproduces up to 8 infra-red remote
control keys to control devices.
Physical Specifications:
Dimensions: 110mm X 65mm X 40mm;
Protection degree: IP20, for indoor use;
Self-extinguishing plastic box UL-94 V0;
Compatibility:
Compatibility with iThink module: V1.0 or higher.
Compatibility with Mordomus software: Mordomus iThink
V2017 or higher.
ATTENTION:
Never remove the circuit board from its housing.
Never crimp or cut cables while they are connected
to powered equipment.
The module is not provided with additional protection
against short circuit, therefore it is recommended to
use a power supply with the correct specifications.
Mordomus shall not be liable for any damages
resulting from the use of our equipment outside the
specifications and/or for a purpose other than that
intended.
Do not install the iMS5 directly exposed to the light of
fluorescent lamps or other light sources;
The light emitted by fluorescent lamps might disturb
iMS5
the learning process of an infra-red command.
The line of sight from the device to the iMS5 should
be unobstructed.
The iMS5 supports most protocols used in remote
controls, however it is possible that there is a specific
remote control that can't be interpreted;
When interfacing with Air conditioners the scheduled
functions of those might not work as expected. Since
the time on these units is set by the remote control,
by repeating a command, the same time will always
be sent to the unit.
Since the iMS5 is a
receiver/transmitter it will not respond to remote
control keys being held (volume up for ex.). In order
to increase the volume, the key has to be pressed for
the number of times necessary to reach the desired
level.
tamper
Overview:
iMS5 MdiBus and power supply connector
Jumper to disable motion detector LED
Jumper to control motion detector sensitivity
Addressing button
iMS5 status LEDs
iPSB connector
Connections:
Specification of MdiBus conductors: CAT 6 UTP
Connection table - refer to image 1, nr.
Terminal of iPSB Cable color
(Eg. Branch 1) (UTP CAT6)
18
Orange
+ 15VDC
18
Brown
+ 15VDC
17 Orange/
GND White
17 Brown/
GND White
17
Shield
GND
16
Green
MDiBus A OUT (Eg. Branch 1)
14
Blue
MDiBus A IN (Eg. Branch 1)
15 Green/
MDiBus B OUT (Eg. Branch 1) White
13 Blue/
MDiBus B IN (Eg. Branch 1) White
HW 1.0
MDiBus and 15VDC power supply connection: The iMS5 should
be connected to the MdiBus and the power supply via the iPSB
module using UTP Cat6 cable.
the previous Table should be respected. The example specifies the
wiring from iMS5 to the branch 1 of the iPSB module.
Connecting more than one iMS5 on the same iPSB branch:
The connection of multiple iMS5 modules in the same extension is
universal infra-red
possible as long as the MDiBus passes through all the iMS5
modules and the last iMS5 module has the MDiBus return
connected to the MDiBus A IN and MDiBus B IN. See
PIR and Tamper inputs connections: The connection of the PIR
and Tamper contacts must be made according to the following
Table and Image 2.
Number
3 PIR (normally closed)
4 PIR (normally closed)
5 Tamper (normally closed)
6 Tamper (normally closed)
LED indicator motion detector
disables the LED indicator of the motion detector. It is advised to
keep this jumper removed as the LED might interfere with the iMS5
luminosity sensor.
PIR sensitivity : Removing this jumper decreases the
sensitivity of the PIR detector (response time). This option is
recommended in cases where the sensor is installed in an
environment with rapid
electromagnetic interferences. For further information refer to the
manual of the motion detector.
and :
Enrollment:
Terminal
of iMS5
To enroll the iMS5 module proceed as follows:
1
1. Make sure that the iMS5 is powered by a suitable
1
power supply and connected to the MdiBus via an
iPSB module
2
2. In the Mordomus software access the menu
2
Configurations and access the sub-menu
Modules/Addresses.
2
3. On the iMS5, press and hold the addressing button
for at least 1sec. The green LED
7
slowly until the addressing is complete.
7
4. The iMS5 should be added automatically to the list
and the green LED
8
8
v.2105
Reset: To perform a reset to the module, interrupt the 15VDC
power supply for 5 seconds.
LED codes:
The wire colors and connections in Green LED ON: Module powered and enrolled to software;
Red LED ON: Module powered and not enrolled to software;
Image 1. Green LED blinking continuously: Module awaiting address
definition;
Red LED flashing: Module sending/receiving data.
Blue LED blinking fast: In learning mode of new infrared signals;
Blue LED flashing: Emission of infra-red signal;
Note: The green and red LEDs are only visible with the cover
image 3.
removed.
This product complies with the Electromagnetic
Compatibility Directive 2014/30/EU.
Function
This product conforms with the EU Directive 2011/65,
RoHS regarding the restriction of use of certain hazardous
substances in electric and electronic devices.
For EU countries only.
All old electrical and electronic devices must be
separated from normal household waste and disposed
of at designated facilities. For further information
contact your local authorities, waste disposal office or
the shop where you bought the device.
: Removing this jumper
http://mordomus.com/mordomus/docs/ithink/iMS5.pdf
http://mordomus.com/mordomus/docs/ithink/iPSB.pdf
temperature changes and/or
and .
will blink
should stop blinking.
2/5