1. Manuales
  2. Marcas
  3. GM Manuales
  4. Accesorios de Automóviles
  5. 19131820
  6. Guia de inicio rapido

GM 19131820 Guia De Inicio Rapido

Ocultar thumbs
1
2
3
4
5
6
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Body Side Molding
Kit Contents
Description
Molding Front (LH)
Molding Front (RH)
Molding Rear (LH)
Molding Rear (RH)
Alcohol Swab
Installation Instructions
Tools Required
Measuring Tape
Masking Tape
Roller
FIGURE 1A
262mm
MASKING TAPE
Body Side Molding
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x
05OC05
11 WHITE 16 POUND NON-BOND
13JN06
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EX-
CLUDING TEMPLATES.
TO BE UNITIZED IN ACCOR-
DANCE WITH GMSPO SPECIFI-
CATIONS.
Quantity
1
1
1
1
4
1
MASKING TAPE
REVISION
I
Vehicle Preparation
1. Temperature must be between 61°F-86°F (16°C-31°C)
2. Wash and thoroughly dry vehicle.
3. Wipe vehicle thoroughly with alcohol swab where receiving
parts. Care and time should be taken on this step to give
good tape adhesion.
4. For best results, vehicle should be free of damage (dents,
scuffs, creases, fractures, etc.)
Body Side Molding Installation
1. Measure from the bottom of the doors and use masking
tape as a guide. See Figure 1A.
2mm
2mm
240mm
REV 13JN08
PART NO.
INSTALLATION INSTRUCTIONS
AUTH
DR
TITLE
PART NO.
19131820
6200 Grand Pointe Dr., Grand Blanc, MI 48439
19131820
SHEET
Chevrolet Corvette
Body Side Molding
SHEET
1
6
OF
1
6
OF
loading

Manuales relacionados para GM 19131820

Resumen de contenidos para GM 19131820

  • Página 1 1. Measure from the bottom of the doors and use masking Measuring Tape tape as a guide. See Figure 1A. Masking Tape Roller FIGURE 1A MASKING TAPE 262mm 240mm MASKING TAPE 19131820 Body Side Molding REV 13JN08 PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE REVISION AUTH...

  • Página 2: Masking Tape

    4. Carefully remove the remaining liner from the Body Side Molding. 2" (50mm) FIGURE 1B MASKING TAPE BODY SIDE MOLDING BODY SIDE MOLDING REAR (RH) 19131820 Body Side Molding REV 13JN08 PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE...
  • Página 3 1. Mesurer depuis le bas des portes et se guider au moyen de Rouleau ruban-cache. Se reporter à la Figure 1A. FIGURE 1A RUBAN-CACHE 262mm 240mm RUBAN-CACHE 19131820 Body Side Molding REV 13JN08 PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE...
  • Página 4 4. Retirer soigneusement le reste de la bande protectrice de la baguette de flanc. 50 mm (2") FIGURE 1B RUBAN-CACHE BAGUETTE DE FLANC BAGUETTE DE FLANC ARRIÈRE (CÔTÉ DROIT) 19131820 Body Side Molding REV 13JN08 PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE...

  • Página 5: Cinta Adhesiva

    1. Mida desde la parte inferior de las puertas y utilice cinta Metro adhesiva como guía. Consulte la Figura 1A. Cinta protectora adhesiva Rodillo FIGURA 1A CINTA ADHESIVA 262mm 240mm CINTA ADHESIVA 19131820 Body Side Molding REV 13JN08 PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE REVISION AUTH...
  • Página 6 2" (50mm) FIGURA 1B CINTA ADHESIVA MOLDURA TRASERA DEL LADO DE LA CARROCERÍA MOLDURA TRASERA DEL LADO DE LA CARROCERÍA (DRCH) 19131820 Body Side Molding REV 13JN08 PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN DATE REVISION...