Remote Control - Revell Control Hexatron FPV Manual Del Usuario

2 reMoTe CoNTrol

2A Display
2B Clockwise/anticlockwise rotation
trim control
2C Trim control for forwards and
backwards flight (Mode 1)
2D Joystick for thrust (Mode 2) or for-
wards and backwards flight (Mode 1)
2E Switch for alternating between Control
Mode 1 and 2
2F Button for flight speed
(40%, 60%, 80% and 100%)
2G Mount for display
2H No function
2I Trim control for forwards and
backwards flight (Mode 2)
3 INSerTINg BaTTerIeS aND DISplay aSSeMBly
3A Slide with light pressure 3E Fit the light shield on
to open the cover one side and carefully
click into place on the
3B Insert 4 x 1.5 V AA
other side of the dis-
batteries and pay
play. Press in lightly to
attention to the polarity,
loosen the sides of the
as shown in the battery
light shield.
compartment.
3F Then insert the display
3C Close the cover again.
with the base facing
3D Carefully fit the display
downwards so the
antenna in the thread and
receptacle clicks into
gently turn clockwise.
the remote control.
4 ChargINg The MulTICopTer aND DISplay
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug the multicopter from the battery, switch off the remote control and plug the
charger into an outlet. The control LED on the charger illuminates green (4A).
• Remove the battery from the battery compartment (do not hold by the cable!) (4B).
• Now plug the battery into the charger. Pay attention to the polarity. Please do not use
force. When the charging process begins, the second LED on the charger illuminates red.
• The charging process lasts approx. 150 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the mains
after the charging is completed (4C).
16
2J Joystick for thrust (Mode 1) or
forwards/backwards flight (Mode 2)
2K ON/OFF switch
2L Trim control for sideways flight
2M Button for video on/off
2N Button for LED on/off
2O Button for photo
2P Battery compartment
2Q Antenna
2R Display base for mount
2S Charge socket
2T Display ON/OFF switch
2U Antenna base
3G Photos and videos can
also be saved on a
micro SD card. Carefully
slide the card with
the contacts facing
downwards into the
slot above the antenna
of the video transmitter
until it clicks into place.
After a charge time of approx. 150 minutes the multicopter can fly for
approx. 5 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
The display has a built-in rechargeable battery. It can be charged with the
accompanying USB charger.
• Plug the USB charger into an open USB port (4D). The LED on the charger illuminates.
• Now insert the plug of the USB charger into the charging socket on the underside of the
display (4E). The LED on the USB charger goes out when the charging process starts.
• T he LED on the charger illuminates again when the battery is fully charged. The
charging process for a fully depleted battery takes about 120 minutes; with a partially
depleted battery it a correspondingly shorter time. The display can be operated for
about 45 minutes with a fully charged battery.
5 STarT preparaTIoN
Mode 1 and Mode 2 toggle (5)
The remote control accompanying the Hexatron FPV can be toggled between Mode1
and Mode2. To do so, move the switch in the centre of the remote control up for Mode
2 and down for Mode 1. In Mode 1, thrust is to the right and forwards and backwards
flight is to the left; in Mode 2 the thrust control is to the left and the control for
forwards and backwards flight is to the right. Important: The remote control must be
switched off to toggle between modes.
The thrust controller (left controller on the remote control) must point down before
switching on (5A). Then set the ON/OFF switch (5B) on the remote control to the
„ON" position and the Power LED begins to blink. Connect the battery cable with the
connecting cable (5C). Now the LEDs on the multicopter begin to blink. Place the
multicopter on the ground so that the tail faces you and both propellers are towards
the front. For the initialisation, the controller for thrust must be briefly moved all the
way up and then back down again. The Power LEDs on the multicopter now illuminate
continuously.
Attention! Make sure that you place your multicopter on a level surface – the control
electronics align their neutral position to the ground!
First switch the ON/OFF switch on the right-hand side to ON for video transmission
(5D). Now connect the battery's balancer connector to the white plug on the
Multicopter (5E). The video transmission will built up automatically in a few seconds.
17