Remote Control - Revell Control Hexatron FPV Manual Del Usuario

2 reMoTe CoNTrol

2A Monitor
2B Rotation trim control
2C Trim control for thrust
2D Control for thrust and rotation
2E Toggle switch for various control
modes – see point 5
2F Button for flight speed
(40%, 60%, 80% and 100%)
2G Mount for monitor
2H Flip button
2I Trim control for forwards/backwards
2J Control for forwards/backwards and
sideways
3 INSerTINg BaTTerIeS aND MoNITor aSSeMBlY
3A Slide with light pressure 3E Fit the light shield on
to open the cover one side and carefully
click into place on the
3B Insert 4 x 1.5 V AA
other side of the mo-
batteries and pay
nitor. Press in lightly to
attention to the polarity,
loosen the sides of the
as shown in the battery
light shield.
compartment.
3F Then insert the monitor
3C Close the cover again.
with the base facing
3D Carefully fit the monitor
downwards so the
antenna in the thread and
receptacle clicks into
gently turn clockwise.
the remote control.
4 ChargINg The MulTICopTer aND MoNITor
Attention: The battery and motor must cool down for 10 to 15 minutes before charg-
ing and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Unplug the multicopter from the battery, switch off the remote control, plug the
power pack into a socket and connect the power pack with the charger. The power
LED on the charger illuminates green (4A).
• Remove the battery from the battery compartment (do not hold by the cable!) (4B).
• Carefully plug the white plug of the Li-Po battery into the Li-Po charger. DO NOT
APPLY FORCE. If the plug is not correctly inserted into the charging socket, the
helicopter may become damaged and, under certain circumstances, become an injury
risk. The LED on the charger illuminates red.
• The charging process lasts approx. 150 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the mains
after the charging is completed (4C).
After a charge time of approx. 150 minutes the multicopter can fly for
approx. 5 minutes.
16
2K ON/OFF switch
2L Trim control for sideways
2M Button for video on/off
2N Button for LED on/off
2O Button for photo
2P Battery compartment
2Q Antenna
2R Monitor base for mount
2S Charge socket
2T Monitor ON/OFF switch
2U Antenna base
2V MODE button
3G Photos and videos can
also be saved on a
micro SD card. Carefully
slide the card with
the contacts facing
downwards into the
slot above the antenna
of the video transmitter
until it clicks into place.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
The monitor has a built-in rechargeable battery. It can be charged with the
accompanying USB charger. Always monitor the charging procedure. A fire-
resistant surface and fireproof environment must always be chosen for the
charging process.
• Plug the USB charger into an open USB port (4D). The LED on the charger illuminates.
• N ow insert the plug of the USB charger into the charging socket on the underside of
the monitor (4E). The LED on the USB charger goes out when the charging process
starts.
• T he LED on the charger illuminates again when the battery is fully charged. The
charging process for a fully depleted battery takes about 120 minutes; with a partially
depleted battery it a correspondingly shorter time. The monitor can be operated for
about 45 minutes with a fully charged battery.
5 TogglINg The FlIghT MoDeS
You can change the configuration of the controllers and accompanying trim. Standard
is the setting "MODE 2".
To do so, switch off the helicopter and remote control.
MODE 1 / MODE 3: Slide the toggle switch (2E) downwards.
MODE 2 / MODE 4: Slide the toggle switch (2E) upwards.
To switch between MODE 1 and MODE 3 or between MODE 2 and MODE 4, press and
hold the MODE button (2V), while turning the remote control back on.
The selected MODE appears on the display.
Mode 1
Mode 1
MODE 1
Forward/Backward Thrust on/o
Forward/Backward Thrust on/o
Turn
left/right
Turn
left/right
MODE 3
Forward/Backward Thrust on/o
Forward/Backward Thrust on/o
Sideways
left/right
Sideways
left/right
Mode 3
Mode 3
MODE 2
Thrust on/o Forward/Backward
Thrust on/o Forward/Backward
Sideways Turn
left/right left/right
Sideways Turn
left/right left/right
MODE 4
Thrust on/o Forward/Backward
Thrust on/o Forward/Backward
Turn Sideways
left/right left/right
Turn Sideways
left/right left/right
Mode 2
Mode 2
Sideways
left/right
Sideways
left/right
Turn
left/right
Turn
left/right
Mode 4
Mode 4
17