Default Settings - Lutron MRF2S-8SD010 Manual De Instrucciones

Stand-Alone Sensor Dimmer /
Switch Programming *
ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
For set-up, programming, and troubleshooting with a
Vive system, please refer to the installation instructions
included with the Vive hub or at www.lutron.com/vive
* Stand-Alone refers to devices that have NOT been
commissioned into a Vive system

Default Settings

Timeout: 15 minutes
Sensor Mode: Occupancy (Auto-On / Auto-Off) 1
PIR Sensitivity: High
Occupied Level: 100%
Vacancy Level: 0%
Fixed ALD Level: Low (when in Fixed ALD mode)
Check Current Settings
2
To display the current settings, tap the Timeout ( ), Sensor Mode (
or PIR Sensitivity ( ) button. The indicator LED ( IL ) that corresponds to
P
the current setting will illuminate.
Tapswitch
Maestro
(on / off)
LEDs
T
ML
IL
Raise
R
Indicator LEDs 2
L
Timeout 4
Lower
P
M
PIR
sensitivity
Sensor
mode 4, 7
PIR lens
Sensor LED
(behind lens)
Sensor dimmer shown
See Test Mode
section.
In order for proper function of device, the device orientation needs to be installed
like shown above.
1 Sensor Mode is locked as "Vacancy" in vacancy only models (MRF2S-8SDV010 and
MRF2S-8SSV).
Only available in stand-alone. Not available when used in a Vive system.
2
3 Only available with the sensor dimmer. Not available with sensor switch.
4 Available in stand-alone. When the device is used in a Vive system, these adjustments are
only available via the Vive software.
5 Learning ALD (Ambient Light Detection): Lights remain off if enough natural light is present.
If the lights turn on and the user does not want that much light, they can tap
5 seconds of entering the space. Similarly, if the lights do not turn on when entering a space
and the user wants more light, they can tap within 5 seconds of entering the space.
T
Over time, the sensor will learn the preferred light level.
Fixed ALD: Lights turn on only when there is less than a set (locked) amount of natural light
6
available. The level can be adjusted in "Fixed ALD Level" settings.
7 This setting will override the sensor mode of the Radio Powr Savr occupancy / vacancy
sensor.
Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036-1299 USA
Default settings in bold
Change Basic Settings
1. Press and hold the desired programming button (
2. Tap the same programming button to cycle to your desired setting.
3. Press and hold the same programming button until the
Timeout M Sensor Mode
4
(determines when lights turn on)
30 minutes Occupancy (Auto-ON / Auto-OFF)
15 minutes Occupancy with Learning ALD
5 minutes Occupancy with Fixed ALD
1 minute Vacancy (Manual-ON / Auto-OFF)
Change Advanced Settings
For complete programming options and additional information, visit www.lutron.com/TechnicalDocumentLibrary/048687.pdf
High-End Trim
3, 4
1. Press and hold and simultaneously until a
100% T R
2. Press and hold until the top
R ML
55%
Alt
3. Hold
30 m L until the desired level is achieved using the top 3 LEDs.
15
5
1
4. Press and hold until the turns off to lock your selection (about 6 seconds).
T
ML
PIR
Mode
Occ
Hi
Med
Lrn
Fixd Low
Low-End Trim Min 3, 4
Vac
1. Press and hold and until a
T L
2. Press and hold L until the bottom
45%
Alt
3. Hold until all bulbs are on and stable (no flickering) or an otherwise desired level is achieved using the bottom 3 LEDs.
30 m R
15
5
1%
1
), 4. Press and hold until the turns off to lock your selection (about 6 seconds).
M T ML
PIR
Mode
Occupancy Level
Occ Hi 1,3,4
Lrn Med
Low
Fixd
Vac Min
The level which the sensor dimmer turns on when motion is detected. This level is adjustable from 1% to 100% within the range of the
low-end and high-end trims.
1. Press and hold and simultaneously until a
M R
100%
2. Press and hold until the top
R ML
Alt
3. Hold until the desired light level is achieved.
L
30 m
15
1%
5
1 4. Press and hold until the turns off to lock your selection (about 6 seconds).
M ML
PIR
Mode
Occ Hi
Med
3 Lrn
Fixd Vacancy Level Low
3, 4
Min
Vac
The level which the sensor dimmer dims or turns off when motion has not been detected for the timeout period.
This level is adjustable from 1% to 100% within the range of the low-end and high-end trims.
Alt
1. Press and hold and simultaneously until a
100% L
M
2. Press and hold until the bottom
L
Alt 2
Alt
3. To set the vacancy level to off, press and hold
30 m
15
3 5 0% the desired light level is achieved.
1
PIR 4. Press and hold until the turns off to lock your selection (about 6 seconds).
Mode M ML
Hi
Occ
Lrn Med
Low
Fixd
Vac Min
Fixed ALD Level 1,2
4 The light level that determines when a sensor will turn lights on or keep lights off when detecting occupancy.
This setting only affects sensors set to "Fixed ALD" mode.
1. Press and hold and simultaneously until an
M Alt
2. The "Fixed ALD" light level will now be displayed by the
3. Press and hold
or until the turns solid to lock your selection (about 3 seconds).
M Alt IL
High (turn ON lights unless area has a lot of light)
Medium
Low
Minimum (turn ON lights only when room is dark)
Walk-through Mode
2
(MRF2S-8SD010 and MRF2S-8SS only)
Alt
Allows the lights to turn off before the Timeout has expired if occupancy is detected only briefly.
30 m
1. Press and hold and simultaneously until an
(unused)
Alt
15
(unused)
5
2. The walk-through setting will now be displayed by the
Disabled
1
3. Press and hold or until the
Alt
Enabled
Electronic Off PIR
2,3
Mode
Alt
Hi
within
T Affects how the lights are turned off. If enabled, the driver will still have power but the lights will be turned off. Occ
30 m Med
Lrn
If disabled, the driver will not have power and the lights will be turned off.
15 Low
Fixd
1. Press and hold and simultaneously until an
5 (unused) Min
Vac M
1
(unused)
2. The electronic off setting will now be displayed by the
Enabled
3. Press and hold or until the
M
Disabled
PIR
Mode
Hi
Occ
Alt
Lutron, Radio Powr Savr, Pico, Maestro, and Vive are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the U.S. and other countries. Med
Lrn
App Store is a service mark of Apple, Inc. Android and Google Play are registered trademarks of Google LLC. iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. Low
Fixd
30 m
© 2019 Lutron Electronics Co., Inc.
Min
Vac 15
5
Customer Assistance | 1.844.LUTRON1 U.S.A. / Canada | +1.888.235.2910 Mexico | +1.610.282.3800 Others | www.lutron.com/support
, , or ) until an flashes (about 3 seconds).
M P IL
turns solid (about 3 seconds). The setting has been saved.
IL
P PIR Sensitivity
1
4 High
Medium
2, 5
2, 6 Low
4 Minimum
begins to flash (about 6 seconds).
ML
is reached and the lights dim up no further.
flashes (about 6 seconds).
ML
is reached and the lights dim down no further.
ML
begins to flash (about 6 seconds).
ML
is reached and the lights dim up no further.
begins to flash (about 6 seconds).
ML
is reached and the lights dim down no further.
ML
until all s flash (3 seconds). Otherwise, hold until
L
ML R
begins to flash (about 3 seconds).
IL
. Tap or to cycle to your desired setting.
IL M
Alt
begins to flash (about 3 seconds).
IL
. Tap or to cycle to the desired setting.
IL Alt
turns solid to lock your selection (about 3 seconds).
IL
begins to flash (about 3 seconds).
IL
. Tap or to cycle to the desired setting.
IL M
turns solid to lock your selection (about 3 seconds).
IL
Test Mode
Test mode has a short timeout (< 15 seconds) that will test the coverage of the sensor with the current settings.
1. Wait at least 2 minutes after power is turned on.
4
2. Press and hold until the PIR lens flashes (about 3 seconds).
T
3. The device will exit test mode after 5 minutes of inactivity or when any button is pressed.
The sensor LED behind the lens will turn on while occupied and turn off while vacant.
Reset Factory Defaults
Note: It may be necessary to reset the device to factory default settings. Before beginning, ensure the device is
connected and powered.
Note: Any associations or programming previously set up with the sensor dimmer / switch will be erased and will
need to be re-programmed after resetting to factory defaults.
1. Triple-tap and hold until the lights begin to flash rapidly; release
T
2. Within 1 second of flashing, release and triple-tap
has been reset to factory defaults.
Troubleshooting
Symptom Possible Causes and Solutions
Lights cannot be manually turned
• Verify proper wiring. Neutral must be connected for product to function properly.
ON or OFF with the newly installed • Wait 10 seconds and try to turn ON or OFF again.
sensor dimmer / switch.
• Wireless device is out of range.
Wireless device will not associate
• Wireless performance is being affected by the physical setup of the space.
to a sensor dimmer / switch.
See Wireless Communication section for more information.
• Sensor modes are limited for vacancy only models
Not all of the sensor modes are
(MRF2S-8SDV010 and MRF2S-8SSV).
available when programming.
• Device may be part of a Vive system.
• Sensor Mode is set to Vacancy (Manual-ON / Auto-OFF).
• The sensor dimmer / switch may be a vacancy only model
Lights do not automatically turn
(MRF2S-8SDV010 and MRF2S-8SSV).
ON when space is occupied.
• The room may be too bright for the current light level setting for
Fixed ALD Level.
Driver / ballast cannot be dimmed
• Verify proper connection of gray and purple wires.
up or down.
• Driver / ballast does not comply with IEC 60929 Annex E.2.
Supports Electronic Off functionality for voltages less than 0.5 V.
Lens flashes when trying to dim
See www.lutron.com/TechnicalDocumentLibrary/048687.pdf
the lights.
Lights flicker when dimmed all the
• Adjust the low-end trim of the driver.
way down.
.
T
again and the lights will flash slowly indicating that the device
T
www.lutron.com/support