Tabla de contenido
INSTALLATION
Tools required:
•
Electric drill
•
Drill bits
•
Phillips
screwdriver
(cross-head)
•
Tape measure
CAUTION: TURN OFF MAIN POWER BEFORE BEGINNING INSTALLATION TO AVOID ELECTRIC
SHOCK.
WALL MOUNTING
Step 1: Read all instructions before installing heater.
Step 2: Unit must be positioned at least 30.5 cm (12 in) away from any adjacent horizontal or
vertical surface. Minimum distance must be maintained.
Step 3: Once the mounting position is decided, mark the drill-holes on the wall for each support.
Step 4: Drill the required holes with diameter a bit smaller than the anchors provided.
Step 5: Insert the anchors.
Step 6: Attach two wall screws into the wall on the top and leave 6 mm (0.25 in) between the wall
and the head of the screw for hanging into the keyholes.
Step 7: Hang the unit on the two wall screws by inserting into the keyholes on the back of the
heater.
Step 8: Attach the third screw at the bottom to secure the unit.
CEILING
MIN
30.5 cm
(12 in)
MIN
MIN
30.5 cm
30.5 cm
(12 in)
(12 in)
MIN
30.5 cm
(12 in)
FLOOR
REMOVING THE HEATER FROM THE BRACKET
Step 1: Lift the unit off the two support screws.
INSTALLATION OF TOWEL BAR (OPTIONAL)
Step 1: Attach the 2 arms of the towel bar with the 2 connection screws and 2 nuts.
Step 2: Attach the arms of the towel bar to the bottom holes of the heater with 4 towel bar
mounting screws (2 for each arm).
CAUTION: DO NOT LOAD HEAVY ARTICLES ON THE TOWEL BAR.
CEILING
MIN
30.5 cm
(12 in)
COOL AIR
INTAKE
WARM AIR
OUTLET
MIN
30.5 cm
(12 in)
FLOOR
15.2 cm (6 in)
38.9 cm
(15.3 in)
ELECTRICAL WIRING
WARNING: THE HEATER MUST BE INSTALLED BY A CERTIFIED ELECTRICIAN AND IN ACCORDANCE
WITH ALL LOCAL AND NATIONAL ELECTRICAL CODES.
WARNING: THIS CONVECTION HEATER IS TO BE USED ON A 240V AC POWER SUPPLY AND BE
CONNECTED WITH A 12-GAUGE, 2-CONDUCTOR WIRE WITH GROUND .
All electrical connections MUST be made inside the junction box located at the backof the unit.
ALL ELECTRICAL CONNECTIONS MUST BE MADE USING THE ELECTRICAL DIAGRAM SHOWN BELOW.
All electrical connections must be secured by twisted-on wire connectors.
HEATER ASSEMBLY
MOTOR
(FAN)
OVERHEAT
TEMP
THERMOSTAT
FUSE
THERMOSTAT OPERATION
Step1: To switch ON 750W heater, adjust the thermostat until a clicking noise is heard;the
indicator light will be turned on and the unit will be at 750W power. The thermostat
maintains the required room temperature by automatically turning on and off the heater.
Adjust the thermostat to increase/decrease the temperature setting.
-
- Turn the thermostat clockwise to increase temperature OR turn the thermostat
counter-clockwise to reduce the temperature setting.
Step 2: To switch OFF the heater, turn the thermostat completely counter-clockwise.
TIMER FOR 1500W HEATER FUNCTION
AND TOWEL WARMING FEATURE
Step 1: The timer can be set up to a 60-minute operating period.
Step 2: Adjust the timer to set the desired operating time up to 60 minutes. Once the pre-set
period is finished, the unit will be switched off automatically and the timer knob will be
turned back to the OFF position. Heater will return to thermostat setting only.
MAINTENANCE
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, ALWAYS SWITCH OFF THE UNIT AND
WAIT 10 MINUTES TO ALLOW IT TO COOL BEFORE ATTEMPTING ANY MAINTENANCE OR CLEANING.
It is recommended that the heater is cleaned periodically, in order to avoid dust blocking the grill
and allow ventilation.
CLEANING
Wipe the unit with a soft damp cloth. Do not use abrasive cleaners or spray liquids on the unit
surfaces.
NOTE: It is possible that the unit surface may discolour (yellow) over time, due to dust or
cigarette smoke. This is normal and not a manufacturing defect.
2
THERMOSTAT
NEUTRAL (WHITE)
TIMER
SWITCH
GROUND (GREEN)
POWER
INDICATOR
LIGHT
LIVE (BLACK)
240V AC, 60Hz
Min
15
30
60
45
Tabla de contenido
