Tabla de contenido
Poorly maintained and lubricated tools can fail unexpectedly.
Keep tool properly lubricated and in good repair at all times. Use only Sioux Air Motor Oil No. 288. See the tool's information sheet
to find out what other greases and oils to use. Do not drop the end of the hose on the floor where it will pick up dirt and transport
it into the tool. See information sheet for any additional maintenance requirements.
Unexpected tool failures can cause injury.
Air hoses can come loose from power tools and whip.
Inspect and do not use tools with loose or damaged air hoses or fittings.
Whipping air hoses can cause injury.
Air hoses that are not oil resistant or are not rated for the working pressure can burst.
Make sure that all air hoses are oil resistant and rated for the working pressure.
Air hoses that burst can cause injury.
Tools not operated at proper air pressure can operate erratically.
Do not exceed a maximum air pressure of 90 psig/6.2 bar or as stated on the tool's nameplate or operating instructions. Use an air
regulator to maintain proper air pressure.
Erratic operation in power tools can cause injury.
Improperly repaired tools perform unpredictably.
Repair tools at an Authorized Sioux Service Center.
Tools that perform unpredictably can cause injury.
Tools left connected to the air supply while making adjustments, changing accessories, or doing any maintenance or service on tool can
start unexpectedly.
Always remove tool from air supply and activate trigger to bleed air line before making any adjustments, changing accessories, or
doing any maintenance or service on tool.
Tools starting unexpectedly can cause injury.
Working in poorly lit areas makes it hard to see hazards.
Keep work area well lit.
Poorly lit work areas can cause injury.
Children are attracted to work areas.
Keep children away. All visitors must keep a safe distance away from work area.
Children in work areas can be injured.
Unauthorized or untrained personnel can misuse unattended tools.
Store idle tools in a dry, high or locked-up place, out of the reach of children.
Misused tools can cause injury.
Tools with the actuator left in the "ON" position when an unexpected air pressure loss occurs can start unexpectedly when the air
pressure is restored.
Release the actuator if an unexpected loss of air pressure occurs.
Unexpected tool starts can cause injury.
Tools with the actuator left in the "on" position can cause unexpected starts when the tool is connected to the air supply.
Be sure actuator is off before hooking up air.
Unexpected starts can cause injury.
The use of any accessory with this tool not provided or specified by Sioux Tools can perform unpredictably.
Use only accessories provided or specified by Sioux Tools.
Tools that perform unpredictably can cause injury.
When disposing of a tool, do it in a way that does not harm personnel or the environment.
INTENDED USE
This tool is intended to drive threaded fastener to join wood, metal and other materials.
GENERAL OPERATION
This tool is equipped with a teasing throttle. By slightly depressing the trigger the bit will rotate slowly. This is useful for starting fastener. The tool will run
at maximum speed when the trigger is fully depressed.
CLUTCH OPERATION INFORMATION
STALL DRIVE ...................................................................................................... Spindle turns with motor. Motor stalls when fastener is tight.
POSITIVE CLUTCH-ANGULAR JAW .................................................................. Spindle doesn't turn with motor. Pressure on spindle engages angular
ADJUSTABLE CLUTCH ...................................................................................... Spindle doesn't turn with motor. Pressure on spindle engages the clutch,
TORQUE CONTROL ........................................................................................... Spindle turns with motor. Applying force from the body of the tool through
ADJUSTABLE CLUTCH OPERATION
Adjustable clutch tools will continue to ratchet when the preset torque is reached and can only be stopped by removing the tool from the fastener.
Adjustable clutches are adjusted externally with the use of Sioux No. 2366 clutch adjustment wrench or a #1 (3/16", 4.8mm Dia. shank) Phillips
screwdriver. Clutch adjustment is accomplished by rotating the clutch cover until the slot in the clutch case appears. Turn the output spindle of the
tool with a 1/4 (6.4mm) hex key wrench until the groove in the adjusting washer is aligned with the slot in the clutch case. Insert the clutch adjustment
wrench into the groove and push to fully engage the teeth. Turn the clutch adjustment wrench counterclockwise to increase the torque.
Three clutch springs are available and are color coded for torque range.
#66050 green spring 2-20 in-lb (.23-2.26 N
#66049 blue spring 15-35 in-lb (1.7-4 N
#66048 silver spring 30-50 in-lb (3.39-5.6 N
Form ZCE844
m)
.
m)
.
m)
.
jaws to turn spindle. Clutch ratchets when certain tightness is reached.
Torque on the fastener is determined by how hard the operator pushes on
the tool.
causing the spindle to turn. When fastener reaches a preset torque, clutch
will ratchet. Adjusting spring pressure will change torque.
the bit causes the tool to run. Once the set torque is reached the tool
stops operation.
2
2021April27/H
Date
Tabla de contenido
