Uline H-1555-20 Guia De Inicio Rapido
Uline H-1555-20 Guia De Inicio Rapido

Uline H-1555-20 Guia De Inicio Rapido

Ocultar thumbs Ver también para H-1555-20:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

π
13-16 STEP ROLLING
SAFETY LADDERS
20 AND 30" DEEP TOP STEP
TOOLS NEEDED
Step Ladder
Rubber Mallet
A. Side Handrail (1)
B. Side Handrail (1) Opposite
C. Rear Handrail Bar (2)
(shipped taped to handrail)
D. Stile (1)
E. Base Panel (1)
WARNING! Assembly of these types of ladders
can be inherently dangerous. Please take all
necessary precautions during the assembly
process. Always use a separate ladder to
finish assembly in high places. Never climb a
ladder that is not completely assembled. Do
not assemble or use a ladder with missing or
damaged parts. Use proper lifting mechanics
when assembling a ladder. Watch for overhead
electrical hazards and obstructions.
PAGE 1 OF 9
1-800-295-5510
uline.com
9/16" Wrench or Socket (2)
7/16" Wrench or Socket
Safety Glasses
PARTS
F. Back Panel (1)
G. Horizontal Brace (2)
ASSEMBLY
STEP 1: FRAME ASSEMBLY
1.
Pour le français, consulter les pages 7-9.
H. Vertical Brace (2)
I. Diagonal Brace (2)
J. Handrail Extension Panel (2)
Notched
Bushing (4)
Handrail Bracket (6)
(shipped attached to handrails)
NOTE: DO NOT tighten bolts until instructed to.
NOTE: Back panel (F) has both round and
slotted holes. The round holes are at the bottom,
and the slotted holes are at the top (L1).
Place the ladder stile (D) on the floor. Be sure to
assemble on a protective surface so the finish does
not get damaged. (See Figure 1)
Para Español, vea páginas 4-6.
Hardware Kit (1)
(misc. hardware included)
Extension Clamps
Set (4)
Gray Bushing (6)
0521 IH-1555-20
Tabla de contenido
loading

Resumen de contenidos para Uline H-1555-20

  • Página 4: Escaleras De Seguridad Con Ruedas De 13-16 Escalones

    π 800-295-5510 uline.mx ESCALERAS DE SEGURIDAD CON RUEDAS DE 13-16 ESCALONES ESCALÓN SUPERIOR DE 50.8 CM Y 76.2 CM (20" Y 30") DE PROFUNDIDAD HERRAMIENTAS NECESARIAS 2 Llaves o Dados 9/16" Escalera Llave o Dado 7/16" Mazo de Hule Lentes de Seguridad PARTES H.
  • Página 5: Continuación De Ensamble

    CONTINUACIÓN DE ENSAMBLE PASO 1: CONTINUACIÓN DE ENSAMBLE DEL MARCO Diagrama 1 2. Utilizando (6) tornillos de cabeza hexagonal de Modelo de un Orificio 3/8-16 x 1⁄" y contratuercas, atornille la parte superior (orificio ranurado) del panel trasero (F) en el interior de L1.
  • Página 6 (4) tornillos de cabeza hexagonal de 1/4-20 x 2¾". (Vea Diagrama 2, Paso 5) NOTA: Ahora ya puede apretar todos los pernos del pasamanos. 800-295-5510 uline.mx PAGE 6 OF 9 0521 IH-1555-20...

Tabla de contenido