Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ENGLISH
DXCM019-0338
Desiccant Air Cleaner - Filter/Dryer, 3/8" NPT
This DeWalt Air Cleaner - Filter/Dryer is a two-part system that consists of a coalescing filter
that removes condensed water, oil vapors and most contaminants and a desiccant dryer that
removes water vapor.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL
US TOLL FREE AT: 1-888-895-4549.
WARNING: For your own safety, read the air compressor instruction manual before using any
accessory. Failure to heed these warnings may result in personal injury and serious damage to the
air compressor and the accessory. When servicing this tool, use only identical replacement parts.
WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust
containing lead. Wash hands after use. Keep out of reach of children.
WARNING: This product can expose you to chemicals including Lead and Cadmium, which are
known to the State of California to cause cancer and birth defects or other reproductive harm. For
more information go to www.P65Warnings.ca.gov.
WARNING: This product is specifically designed for compressed air service ONLY.
COMPONENTS (FIG. 1)
A. Service indicator
B. Mounting bracket
C. Coalescing filter bowl
D. Dryer bowl
E. Inlet
F. Outlet
G. Drain valve
TYPICAL INSTALLATION
WARNING: ALWAYS turn compressor OFF, disconnect from power source, and drain all pres-
sure from system before servicing.
Note: Air supply must be dry enough to avoid ice formation at temperatures below 35°F (2°C).
Note: These products are designed specifically for compressed air service only.
Note: Use a thread sealer or Teflon® tape on all male threads.
1. Securely mount the air cleaner/dryer in a vertical position as close as possible to air tool
connection using the mounting bracket supplied with the unit.
Note: Air flow must be in same direction as arrows on top of the unit. Verify the arrow points to the
outlet (F).
2. System piping should be 3/8" minimum. Avoid using unnecessary fittings, couplings, etc., that
restrict the flow of air.
3. Remove the dryer bowl (D) by pushing in towards the filter body, turning counterclockwise and
then pull bowl down.
4. Pour the bag of desiccant (included) into the bowl, gently shake or tap the bowl to settle the
desiccant. Fill to within 1/2" from the top of the bowl. Avoid getting any of the desiccant in the
center tube.
5. Reinstall the bowl on the filter body by lining up the tabs, pushing the bowl in towards the filter
body and turning clockwise to lock into place. Make sure the bowl is tight before pressurizing
the unit.
6. The coalescing filter bowl (C) is supplied with the filter element pre-installed.
7. Make sure the air hose or air line used to connect the air cleaner/dryer outlet (F) is clean to
prevent contamination of the cleaned air. Connect the air supply to the inlet port (E).
8. Turn on the air supply and check for any air leaks.
OPERATION
WARNING: ALWAYS depressurize the unit before removing the bowl. Personal injury and/or
property damage could occur. If bowl is difficult to remove, it may be under pressure.
1. Before pressurizing system, make certain the coalescing bowl (C) and the dryer bowl (D) are
securely locked into the filter body.
2. Check that all connections are tight. A small leak will substantially reduce the performance
of your compressor. If you suspect a leak, spray a small amount of soapy water around the
area with a spray bottle. If bubbles appear, retighten or reseal the connection. Do not
overtighten.
MAINTENANCE
1. Before each use, drain moisture from the coalescing bowl before each use by turning the drain
valve (G) so that the arrow points downward. Make sure the system pressure is 10 psig or less.
2. The only two items that require servicing on the air cleaner/dryer is replacement of the desiccant
when the desiccant turns pink and replacement of the filter element when the service indicator
(A) pops up.
DESICCANT REPLACEMENT
a. Turn off the air supply to the air filter/dryer and drain air pressure from the system.
b. Remove the dryer bowl (D) by pushing in towards the filter body, turning counterclockwise
and then pull bowl down.
c. Empty the used desiccant.
d. Pour new desiccant into the bowl, gently shake or tap the bowl to settle the desiccant. Fill to
within 1/2" from the top of the bowl. Avoid getting any of the desiccant in the center tube.
e. Reinstall the bowl on the filter body by lining up the tabs, pushing the bowl in towards the
filter body and turning clockwise to lock into place. Make sure the bowl is tight before
pressurizing the unit.
COALESCING FILTER REPLACEMENT
a. The service indicator on the coalescing filter indicates when the filter element needs to be
changed. When the service indicator (A) pops up, the filter element must be replaced.
b. Turn off the air flow to the air cleaner/dryer and drain pressure from the system.
c. Remove the coalescing bowl (C) by pushing in towards the filter body, turning
counterclockwise and then pull bowl down.
d. Unscrew the used filter element by turning counterclockwise.
e. Install a new filter by gripping the bottom of the filter element and screw it clockwise into the
FIG. 1
filter body. The filter can be damaged if foam coating is compressed during installation.
NOTE: filter elements cannot be cleaned. A new filter must be used.
f.
Reinstall the bowl on the filter body by lining up the tabs, pushing the bowl in towards the
filter body and turning clockwise to lock into place. Make sure the bowl is tight before
pressurizing the unit.
3. Before placing the unit in service, make sure both bowls are reinstalled and securely locked in
place.
WARNING: Never operate the air filter/dryer without the bowls locked securely in place.
Maximum inlet pressure
Maximum outlet pressure
Air Inlet/outlet
Element
Flow rate
WARNING: ALWAYS turn compressor OFF, disconnect from power source, and drain all pres-
sure from system before servicing. Personal injury and/or property damage could occur.
WARNING: ALWAYS drain air pressure from the unit before removing the bowl. Personal injury
and/or property damage could occur. If bowl is difficult to remove, it may be under pressure.
WARNING: RISK OF ELECTRIC SHOCK, FIRE, AND/OR INJURY. Keep the work area clean
and well lighted. Cluttered benches and dark areas increase the risks of electric shock, fire, and
injury to persons. Place cleaning rags and other flammable waste materials in a secured metal
container. The container should be disposed of properly in accordance with local, state, and fed-
eral regulations.
WARNING: RISK OF EXPLOSION AND/OR FIRE. Do not operate the tool in explosive atmo-
spheres, such as in the presence of flammable liquids, gases, or dust. The tool is able to create
sparks resulting in the ignition of the dust or fumes.
WARNING: RISK OF INJURY. Keep bystanders, children, and visitors away while operating
the tool. Distractions are able to result in the loss of control of the tool.
WARNING: RISK OF INJURY. Dress properly. Do not wear loose clothing or jewelry. Contain
long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long
hair increase the risk of injury to persons as a result of being caught in moving parts.
WARNING: RISK OF HEARING LOSS. Always wear ANSI S3.19 approved ear protection when
using the tool. Prolonged exposure to high intensity noise is able to cause hearing loss.
WARNING: RISK OF EYE INJURY. Always wear ANSI Z87.1 approved safety goggles when
using an air tool. Air powered equipment and power tools are capable of propelling materials such
as metal chips, sawdust, and other debris at high speed which could result in serious eye injury.
WARNING: RISK OF INJURY. Disconnect the tool from the air supply when not in use. NEVER
change accessories or perform maintenance or service operations while the tool is connected to
the air supply.
WARNING: RISK OF BURSTING AND/OR INJURY. Check for damaged air hose. Keep the
air hose away from heat, oil, and sharp edges. Inspect the air hose periodically and replace it if it
becomes worn or damaged.
WARNING: RISK OF INJURY. Tool service must be performed only by qualified repair person-
nel.
WARNING: RISK OF INJURY. When servicing a tool, use only identical replacement parts. Use
only authorized parts.
WARNING: Some chemicals are harmful to the Polycarbonate bowls. These chemicals
include Toluene, Benzene, Acetone, Solvents and Ammonia to name a few. Always check for
these chemicals and review the MSDS sheet of the product being used for potential interaction
with Polycarbonate materials.
WARRANTY
ONE YEAR LIMITED WARRANTY: DEWALT Industrial Tools (the Company) warrants that for a
period of twelve (12) months from the date of purchase, it will replace or repair, free of charge,
for the original retail purchaser only, any part or parts, manufactured by the Company, found
upon examination by the Company or its assigned representatives, to be defective in material
or workmanship or both. All transportation charges for parts submitted for replacement or repair
under this warranty must be borne by the original retail purchaser. This is the exclusive remedy
under this warranty.
Failure by the original retail purchaser to install, maintain and operate said equipment in accor-
dance with good industry practices, or failure to comply with the specific recommendations of the
Company set forth in the owner's manual, shall render this warranty null and void. The Company
SPECIFICATIONS
220 PSI (15 bar)
150 PSI (10 bar)
3/8" NPT (F)
40 Micron
100 SCFM @ 90 PSI
loading

Resumen de contenidos para DeWalt DXCM019-0338

  • Página 1 DXCM019-0338 Desiccant Air Cleaner - Filter/Dryer, 3/8” NPT This DeWalt Air Cleaner - Filter/Dryer is a two-part system that consists of a coalescing filter that removes condensed water, oil vapors and most contaminants and a desiccant dryer that removes water vapor.
  • Página 2 Ce purificateur d’air avec déshydratant - filtre/séchoir DeWalt est un système en deux parties, Remarque : Les éléments du filtre ne peuvent pas être nettoyés. Un nouveau filtre doit être utilisé.
  • Página 3 Asegúrese de que el depósito esté bien apretado antes de presurizar la unidad. Este purificador de aire con desecante – filtro/secador DeWalt es un sistema de dos partes que consiste en un filtro coalescente que elimina el agua condensada, los vapores de aceite y la 3.
  • Página 4 DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an affiliate thereof and are used under license. The yellow/black color scheme is a trademark for DEWALT power tools & accessories.