Black and Decker CS36BS Manual Del Usuario página 6

ENGLISH
Features
1. On/off trigger
2. Forward/reverse slider
3. Bit holder (1`/4" Hex Shank)
4. LED light
5. Bit storage
5a. Magnetic bit/screw holder
Assembly
Fitting and removing a drill bit or a screwdriver bit
(fig. A)
This tool uses screwdriver bits and drill bits with a 6.35 mm
(1/4") hexagonal shank. The tool can store 8 of these bits in
the bit storage compartment (5) or individually in the magnetic
bit/screw holder (5a) as shown in figure D.
To fit a bit, insert the bit shaft into the bit holder (3).
u
To remove a bit, pull the bit shaft out of the bit holder (3).
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Before first use, the battery must be charged for at least
u
10 hours.
Charging the battery (fig. B)
Insert the charger plug (7) into the charger connector (6).
u
Plug in the charger (7).
u
Leave the tool connected to the charger for
u
The charger may hum and become warm while charging; this
is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40°C.
Selecting the direction of rotation (fig. C)
For tightening screws, use forward rotation.
For loosening screws or removing a jammed drill bit, use
reverse rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the forward position.
To select reverse rotation, push the forward/reverse slider
u
(2) to the rearward position.
To lock the tool, set the forward/reverse slider into the
u
centre position.
Screwdriving
Select forward or reverse rotation using the forward/
u
reverse slider (2).
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch (1).
u
LED light
The LED light (4) is activated automatically when the trigger
is depressed. The LED will also illuminate when the trigger is
6
(Original instructions)
10 hours.
depressed and the forward/reverse slider (2) is in the locked
off position (central position).
Hints for optimum use
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Use the spindle lock to loosen very tight screws or to
u
firmly tighten screws.
Always hold the tool and screwdriver bit in a straight line
u
with the screw.
When screwing in wood, it is recommended to drill a
u
pilot hole with a depth equal to the length of the screw.
A pilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a clearance hole with
u
a depth equal to half the length of the screw.
For the optimum size of the clearance hole, refer to the
table below.
Screw size Pilot hole ø
(softwood)
Nr. 6 (3.5 mm) 2.0 mm
Nr. 8 (4 mm) 2.5 mm
Nr. 10 (5 mm) 3.0mm
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER and Piranha accessories are engineered
to high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35 mm)
hexagonal shank. Piranha Super-lok accessories are
designed for use with this tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning. Your
charger does not require any maintenance apart from regular
cleaning.
Warning! Before performing any maintenance on the tool,
switch off and unplug the tool or remove the battery from the
tool if the tool has separate battery. If the battery is integral,
run the battery completely down. Unplug the charger before
cleaning it.
Pilot hole ø Clearance hole
(hardwood)
2.5 mm 3.6 mm
3.0 mm 4.5 mm
3.5mm 5.0mm