Premier PR970 Manual Del Usuario página 6

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
Remote Message Playback
Call your unit from a touch tone telephone.
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
Then you can press "1#" or "2#" on your keypad and the PR970 will playback the messages
recorded in Mailbox 1 or Mailbox 2, respectively.
Remote Record New Greeting
The PR970 enables you to change your outgoing greeting from a remote phone.
Call your unit from a touch tone telephone.
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
Press "8#".
When you hear a beep, begin recording your new greeting (up to 30 seconds).
When you have finished recording your new greeting, press "5#".
The unit will beep, and the new greeting will playback to you.
Hang up the telephone.
Remote Record Memo
Call your unit from a touch tone telephone.
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
Press "3#". Then within three seconds of pressing "3#" press "1#" or "2#" to select Mailbox
1 or Mailbox 2. Otherwise the memo will be recorded in Mailbox 1.
When you hear a beep, begin recording your memo (up to 60 seconds).
When you have finished recording your memo message, press "5#".
Remote Turn Off Answer On
If you forget to turn off the answer mode of your PR970, you can do this from a remote phone.
Call your unit from a touch tone telephone.
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
Press "9#".
You can now hang up.
PR970 – 9
Repeat Current Message
Press "4#" WHILE you are listening to the message. The message will be played again.
All following messages will then be played as usual and will be memorised when you hang
up.
Erase Current Message
Press "0#" WHILE you are listening to the message you wish to erase. The message will be
played to the end.
The following messages can be erased in the same way.
When you hang up, the message(s) will be automatically erased.
Repeat Previous Message
Press "4#" repeatedly WHILE you are listening to the message. The previous message will be
played again.
All following messages will then be played as usual and will be memorised when you hang
up.
Stop Message Playback
Press "5#" WHILE you are listening to the message.
All messages will be memorised when you hang up.
Skip to Next Message
Press "6#" WHILE you are listening to the message. The next message will be played.
All following messages will then be played as usual and will be memorised when you hang
up.
IMPORTANT!
If your appliance is not operating properly before contacting a Service Center we advise you to
do a "RESET" of your unit. In many cases, the appliance will again function normally after you
have done this.
To reset unit:
Unplug the telephone line from the wall jack.
Unplug the AC adapter from the power outlet.
Remove the AAA batteries, and then replace.
Plug the AC adapter back into the power outlet.
Plug the telephone line back into the wall jack.
Record a new outgoing greeting or you can use the pre recorded announcement.
Reset the Voice Day/Time Stamp.
ATTENTION!
This RESET erases all information (e.g. programmed day and time indication, outgoing greeting,
etc. will be erased)!
PR970 – 10
Tabla de contenido
loading

Tabla de contenido