Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Selecting the programmes
and special functions
Use in conjunction with programme guide
Setting a programme
I
Open the door and press the
button; the 5
programme selection indicator lights start flashing
to show that the machine is waiting for a selection
to be made.
Press the Programme Selection Button "P" and
the indicator light for the heavy wash program-
me will start flashing. Set the required programme
by pressing the Programme Selection Button
again. When then light for the required programme
starts flashing, close the door and when the
audible signal has sounded (if it has not been
deactivated)
the
programme
will
start
automatically.
E
Economy button
The "E" button reduces the temperature of the
water during the last rinse. This activates a natural
drying process, as with a normal draining board,
simply by leaving the door ajar at the end of the
cycle to enable the natural circulation of air. The
"E" button provides an energy saving of more
than 20% and shortens the cycle.
Recommended for evening washes when the
dishes are not required perfectly dry, straight
away.
Interrupting a programme
It is not recommended that the door be opened
while a programme is running, and especially
not during the main wash phase and final
drying.
However, the appliance stops automatically
when the door is opened. At this point the "E"
button can be programmed or cancelled.
When the door is closed again, the programme
continues automatically. If you wish to change
or cancel a programme which is running, carry
out the following procedure:
open the door, keeping the Programme Selection
Button "P" pressed in until all 5 indicator lights
are flashing. A new setting can now be made.
NB: If, on pressing the Programme Selection
Button "P" the indicator lights start flashing
alternately, it means that there is water in the
machine.
Close the door to allow the water to be discharged
and wait for the audible signal, after which the
new programme can be set.
Before starting a new programme, you should
check that there is still detergent in the dispenser.
If necessary, top up the dispenser.
End of programme
The end of the programme is indicated by an
audible signal. When the door is opened the 5
programme selection indicator lights start flashing.
Release the
button.
I
Activating and Deactivating the audible
signal
The audible signal function can be deactivated
in the following way:
keep the Programme Selection Button "P"
pressed in for a few seconds and at the same
time press the On/Off button; if the three indicator
lights "Intensive programme", "Regular
programme" and "R 32' Rapid programme"
are illuminated, the audible signal is activated.
By pressing the Programme Selection Button
"P" again, the "Normal programme" and "Eco
programme" lights will come on, which means
that the audible signal has been deactivated.
An audible signal sounds to indicate that the
setting has been stored in memory.
Attention
This dishwasher is equipped with an anti-overflow
safety device which works even when power is
switched off and and if the water level is too high
the supply will automatically be closed off.
Important
To ensure the correct operation of the anti-overflow
safety device, it is recommended not to move or
to tilt the dishwasher during
operation.
If it is necessary to move or to tilt the dishwasher,
first make sure the washing cycle is finished and
that no water is left in the tank.
18
Regulating the water softener
with electronic programmer
The water softener can treat water with a hardness level of up to 90°fH (French
grading) or 50°dH (German grading) through 6 settings.
The settings, are listed in the panel below:
Water
hardness
Level
°fH
(French)
0
0-5
1
6-15
2
16-30
3
31-45
4
46-60
5
61-90
The softener unit is set in the factory at level 3 (Indicator light N.3) as this satisfies
the requirements of the majority of users. Regulate the setting of your water softener
unit according to the degree of hardness of your water as follows: open the door,
keep button "E" pressed in for a few seconds and at the same time press the On/Off
button
.
I
The indicator light of button "E" will start flashing and indicator light N.3 (the factory
setting) will come on. To change the setting, press button "E". Each time you press
that button, the next indicator light will come on. When the required indicator light
comes on, wait for the audible signal to confirm that the new setting has been stored
in memory.
N°1 N°2 N°3 N°4 N°5
Water
Use of
Water
hardness
regenerating
softener
°dH
salt
setting
(German)
0-3
NO
Indicator light N.1
4-9
YES
Indicator light N.1
10-16
YES
Indicator light N.2
Indicator light N.3
17-25
YES
Indicator light N.4
26-33
YES
Indicator light N.5
34-50
YES
ON/OFF
BUTTON
BUTTON E
19
Tabla de contenido
