Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Operating Instructions and Parts Manual
Figure 6 - Horizontal Tank
Air Volume Control
Hose
Coupling
Figure 7 - Vertical Tank
Installation
(Cont'd)
3. Install a valve and isolating hose
between the system and the house
plumbing to aid in pump removal for
servicing and for reducing noise trans-
mitted through the house piping.
4. Provide a hose bib (faucet) at the
lowest point in the system to drain
for service or storage.
DEEP WELL PUMP WITH PRECHARGED
STORAGE TANK (FIGURE 8)
1. Check tank precharge using a tire
pressure gauge. The precharge pres-
sure should be 28 - 30 psi on 1/2, 3/4
and 1 HP models.
2. Check the pressure with the power
off, faucets open and no water
flowing (zero water pressure).
3. Install a valve and isolator hose
between the system and the house
plumbing to aid in pump removal
for servicing and for reducing noise
transmitted to the house through
the piping.
4. Provide a hose bib (faucet) at the
lowest point in the system to drain
for service or storage.
Pressure
Switch
Air
Volume
Control
Tubing
Air
Volume
Control
Figure 8 - Precharged Storage Tank
CONVERTING THE DEEP WELL PUMP TO
Air
SHALLOW WELL OPERATION (FIGURE 9)
Volume
Control
For shallow wells (25 feet or less), a
Tubing
bolt-on shallow well jet is available as
an accessory for deep well pumps. The
jet attaches to the front of the pump
with the two bolts provided and con-
verts the deep well pump into a shal-
low well pump. The shallow well jet has
a 1" NPT inlet and a 1/8" NPT opening
for an air volume control. For optimum
performance, an incline check valve on
the inlet side of the shallow well jet is
recommended
Figure 9 - Shallow Well Jet
Electrical
designed for indoor installation only.
The voltage of power supply must
match the voltage of the pump. All
above ground well pumps except
CHART 3 - RECOMMENDED FUSE & WIRING DATA - 60 HZ MOTORS
HP
Volt
115
1/2
230
115
3/4
230
115
1
230
SWS50BOOST have dual voltage motors
Pressure
preset at the factory to 230 volts. The
Switch
motors can be converted to 115 volts by
turning the voltage selector to the
desired voltage (See Figure 10). Use a
needle nose pliers to pull the selector
out approximately 1/4", rotate and
then reinsert in correct position.
Figure 10 - Voltage Selector
Select the proper size wire and fuse
(Chart 3). Time delay fuses are recom-
mended over standard fuses for motor
circuit protection. All pump motors
To Air Volume
have built-in automatic overload pro-
Control
tection that will prevent damage to the
motor due to overheating.
Jet
ply until unit is permanently grounded.
Connect ground wire to approved ground
then connect terminal provided.
A metal underground water pipe or
Risk of electrical
well casing at least 10 feet long makes
shock. This pump is
the best ground electrode. If plastic
pipe or insulated fittings are used, run
a wire directly to the metal well casing
or use a ground electrode furnished by
the power company.
Dual
Element
Fuse
250V
15
14
10
14
15
14
10
14
20
12
10
14
5
Do not connect to
electric power sup-
Distance In Feet
From Meter To Motor
0
51
101
To
To
To
50
100
200
Wire Size
14
12
14
14
14
10
14
14
12
10
14
14
www.waynewatersystems.com
JCU50
201
To
300
10
14
8
14
8
14
Tabla de contenido
