UNIPRODO UNI HEATER 03 Manual De Instrucciones página 7

EN
38,5cm
On the back of the remote control, remove the
protective coating of the battery (1) – to do this, pull it
out of the battery compartment (2) by pulling it towards
you (3).
CAUTION: if the protective coating is not removed
despite the efficient battery, the remote control will not
work!
INSTALLATION/REPLACEMENT OF THE REMOTE
CONTROL BATTERY
Symptoms of a depleted remote control battery include
weak or no response to the buttons on the remote. To
remove the battery compartment, press and hold the
compartment lock (5), and with the help of a fingernail
or a sharp object, lift the battery compartment and pull
it towards you away from the remote control (4).
4
2
1
3
5
CAUTION: When installing batteries in the remote
control, pay attention to the correct polarity.
5
3.3. DEVICE USE
3.3.1. STANDBY MODE
After installing the device on a vertical wall, connect the
plug to the power source and then set the switch on
the side of the device (1) to the ON – „I" position. The
message „S" will appear on the display, which means
that the device is in the standby mode, i.e. ready for
operation.
3.3.2. TURNING ON/OFF THE DEVICE
Press the ON/OFF button on the device control panel
(4) or remote control (1) to turn on the device. It will
automatically switch to a blowing mode, and the display
will show the message „- -"
3.3.3. SETTING THE HEATING POWER
Press the heating power selection button on the control
panel (5) or on the remote control (4) to select one of
the two heating settings. Default setting „I" – 1000 W.
Pressing the same button again changes the power
to „II" – 2000 W. The appropriate selection is signaled
adequately by one or two lights on the device control
panel (2).
12
3.3.4. SETTING THE TIMER
The timer function counts down the device operating
time until it is automatically turned off, i.e. it enters the
standby mode. Available hours range: 0-12. Press the
timer button on the control panel (6) or on the remote
control (2), the display will show the current time. Each
press of the timer button increases the operating time
of the device by one hour. After selecting the desired
operating time, it will be shown on the display for
about 5 seconds, followed by the timer indicator on
the display, and the display itself will show the previous
parameter.
3.3.5. SETTING THE STARTUP TIME
You can set the time for automatic activation and
operation of the device. To do this, when the device
is in the standby mode, press the timer button on the
control panel (6) or on the remote control (2). After
setting the time in the range of 0-12 hours, the device
will display the set time until automatic start-up and the
timer indicator (8) will light up – this time will be counted
down and after it has expired, the device will start
automatically. The default heating temperature is 23 oC.
CAUTION: if the heating temperature has not been
set and no operating mode has been programmed,
the device will automatically turn off after 12 hours of
continuous operation.
3.3.6. PROGRAMMING THE OPERATING MODE
CAUTION: this operation can only be programmed
using the remote control!
A. Setting the time and day of the week.
In the standby or operating mode, set the time and
day of the week. Press the "SET" button (3) and
the display will show "12" as the default hour. Use
the parameters increasing or decreasing buttons
(5) to set the current hour, then by pressing the
"SET" button (3) to accept the set hour to go to the
minutes setting. The minutes are also set with the
same buttons (5) and confirmed with the "SET"
button (3). After setting the time, the weekday
"d1" will appear, which is Monday by default. Use
the parameters decreasing or increasing buttons
(5) to set the current day of the week ("d1" – "d7"
respectively Monday–Sunday), and then press
the "OK" button to confirm the settings. The time
setting range is 00–23 hours and 00–59 minutes.
Below is an example of setting 9:30 for Wednesday:
CAUTION: the device must be reset after power is
removed. Then use the „SET" button (5) to check if the
time and day of the week are correct.
B. Blowing temperature setting
During operation, press the parameter
decreasing/increasing button (5), the display will
show „23" as the default heating temperature.
If necessary, use the same buttons (5) to set the
desired temperature (in the range of 10–49 oC),
and confirm it with the „OK" button (5).
C. Setting the weekly operation mode.
After previous setting of the time and day of the
week, you can program the weekly operation
mode of the device.
a) Press the ON/OFF button on the device's panel (4)
or remote control (1) to start the device.
b) Press the program selection button (8) to enter the
weekly program settings – the program indicator
will light on the display.
c) Press the button for setting the day of the week
(7) on the remote control, and after displaying
the default day „d1" (Monday) set the current
day by pressing the same button (according to
the diagram: („d1" – „d7" respectively Monday–
Sunday) as necessary.
Message D1 D2 D3
Day of
Monday Tuesday Wednesday
the week
Message D4 D5 D6 D7
Day of
Thursay Friday Saturday Sunday
the week
d) Press the time of day edit button (10) on the
remote control, the display will show „P1". By
pressing the same button again, we can choose
one of the six times (P1–P6) for a given day with
the setting of any time and temperature.
13 EN
e) Press the ON time setting button on the remote
control (9), the display will show „00". The next
pressing of the same button increases the time of
starting the device by one hour, etc. according to
this scheme - the time range from 00 to 24 can
be selected. For example, in the picture below,
turning on at 7:00:
f) Press the switching-off time setting button (11)
on the remote control, the device will show the
default switching-on time on the display. The
switching-off time is set in a similar way as in the
case of setting the switching-on time (selectable
time range from 00 to 24), with the difference
that the specific time is selected using the off time
button (11) on the remote control.
CAUTION: the time of automatic switching off
of the device cannot be earlier than the time of
switching on! If the hours are the same, the device
goes into the standby mode – yes.
g) Use the parameter increasing/decreasing buttons
(5) to set the desired temperature (within the
range of 10–49 oC).
h) By repeating steps c)–g) you can set the operating
parameters for each day of the week.
i) Press the „OK" parameter confirming button (5)
on the remote control to finish programming.
CAUTION: when working in the programmed
mode, by pressing the button for setting the
day of the week on the remote control (7), you
can enter the settings for a given day and then
using the program editing button (10) to check the
automatic start time, and by pressing the same
button again, the automatic stop time.
j) To cancel the weekly program mode, press the „P"
button (8) on the remote control.
3.3.7. ACTIVATION/DEACTIVATION OF THE OPEN
WINDOW DETECTION
After turning on the device, press the button for the
open window detection function (6) on the remote
control using the ON/OFF button (on the control panel
4 or on the remote control 1). Indicators (7) and (9) will
light up on the display of the device. The display will
show the default temperature „23". This temperature
can be changed with the parameter decreasing/
increasing buttons (5). If the device detects a drop
in room temperature, it will stop working. To switch
the device back on, press the ON/OFF button (on the
device panel 4 or on the remote control 1). Pressing the
button for the open window detection function (6) again
deactivates it – the function indicator on the display (7)
turns off.