Packing List - EGO ST1500E-F Traducción De Las Instrucciones Originales

EN
Measured sound power level L
Sound pressure level at
operator's ear L
PA
Guaranteed sound power level L
(according to 2000/14/EC)
Front-assist Handle
Vibration a
h
Rear Handle
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾
The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE:
The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used;In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.

PACKING LIST

PART NAME
Line Trimmer
Guard
Front-assist Handle Assembly
Shoulder Strap
Hex Wrench
Operator's Manual
DESCRIPTION
KNOW YOUR LINE TRIMMER (Fig. A)
1. Trigger
2. Rear Handle
3. Lock-off Lever
4. Soft Sleeve
5. Adjustable Front-Assist Handle
6. Shoulder Strap
7. Cutting Line
8. Guard
9. Line-Cutting Blade
10. Release Tab
11. Trimmer Head (Bump Head)
10
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1500E-F
92.24 dB(A)
K=0.96 dB(A)
WA
72.24 dB(A)
K=3.0 dB(A)
96 dB(A)
WA
3.118 m/s
2
K=1.5 m/s
2
2.902 m/s
2
K=1.5 m/s
2
QUANTITY
1
1
1
1
1
1
12. Ejection Mechanism
13. Electric Contacts
14. Latch
15. Battery-Release Button
ASSEMBLY
WARNING:
If any parts are damaged or missing,
do not operate this product until the parts are replaced.
Use of this product with damaged or missing parts could
result in serious personal injury.
WARNING:
Do not attempt to modify this product
or create accessories not recommended for use with
this Line trimmer. Any such alteration or modification is
misuse and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the tool when assembling parts.
MOUNTING THE GUARD
WARNING:
Always wear gloves when mounting or
replacing the guard. Take care of the blade on the guard
and protect your hand from cutting.
WARNING:
Never operate the tool without the guard
firmly in place. The guard must always be on the tool to
protect the user! When the guard is fixed, never attempt to
remove or adjust the guard, if a replacement is needed, it
should be performed by a qualified service technician!
Loosen and remove the two screws from the shaft base
(Fig. B), align the guard mounting holes with the assembly
holes and then lock the guard onto the shaft base with the
two screws, together with two spring washers (Fig. C).
Make sure the guard is fixed according to Fig. B & C, any
reverse fixing will cause great danger!
MOUNTING AND ADJUSTING THE FRONT-ASSIST HANDLE
Push the front-assist handle onto the shaft (Fig. E), then
insert the clamping block into the handle slot (Fig. F), mount
the lock pole, and lock them with the wing nut (Fig. G). The
sequence is as Fig. D shown. Lastly, adjust the front-assist
handle between the soft sleeve and the label to make sure
your front arm is straight when using the trimmer (Fig. H)
and then lock the lever of the lock pole (Fig. I).
Fig. D & H parts description see below:
D-1 Front-assist Handle
D-2 Lock Pole
D-3 Clamping Block
D-4 Wing Nut
H-1 Soft Sleeve
H-2 Warning Label