Safety Warnings Specific For Sanding Operations - Skil 8100 Manual Original

into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The
wheel may either jump toward or away from the operator,
depending on the direction of the wheel's movement at
the point of pinching. Abrasive wheels may also break
under these conditions.
• Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque
reactions or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory.
The accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs. Kickback will
propel the tool in the direction opposite to the wheel's
movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create frequent
kickback and loss of control.
3) SAFETY WARNINGS SPECIFIC FOR SANDING
OPERATIONS
a) When sanding, do not use excessively oversized
sanding disc paper. Follow the manufacturers'
recommendations when selecting sanding paper.
Larger sanding paper extending beyond the sanding
pad presents a laceration hazard and may cause
snagging, tearing of the disc, or kickback.
4) SAFETY WARNINGS SPECIFIC FOR POLISHING
a) Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely. Tuck
away or trim any loose attachment strings. Loose
and spinning attachment strings can entangle your
fingers or snag on the workpiece.
ADDITIONAL SAFETY WARNINGS
GENERAL
• This tool should not be used by people under the age
of 16 years
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
• Ensure that children do not play with the tool
• This tool is not suitable for wet sanding
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
• Only use the flanges which are supplied with this tool
• Never use accessories with a "blind" threaded hole
smaller than M14 x 22 mm
Never use grinding/cutting discs with this tool
•
OUTDOOR USE
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
• Before using the tool for the first time, it is recommended
to receive practical information
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
• Keep hands away from rotating accessories
• Do not continue to use worn, torn or heavily clogged
sanding sheets
• When sanding metal, sparks are generated; do not
use vacuum cleaner and keep other persons and
combustible material from work area
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• In case of current interruption or when the plug is
accidentally pulled out, immediately switch off the tool in
order to prevent uncontrolled restarting
AFTER USE
• After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Wear protective glasses and hearing protection
6 Do not dispose of the tool together with household waste
material
8