SKIL MASTERS 3855 Manual Del Usuario página 19

- irmly clamp the workpiece by turning down knob K4
For horizontal clamping 0b
- remove clamp from holder using knob K5
- position clamp into support hole K6 as illustrated (on
either side of the tool)
- press the workpiece irmly against fence L
- irmly clamp the workpiece by turning down knob K4
• Setting mitre angles @
- loosen locking handle M
- rotate the saw table to the left or right and set the desired
mitre angle (from 0° to 47°) by using indicator M1
- tighten locking handle M (do not tighten the handle
too firmly)
- for quick and precise setting of often used mitre angles
(0°, 15°, 22.5°, 30°, 45°) the saw table clicks into place
at the corresponding positions
• Setting bevel angles #
- loosen three-legged knob N
- swing the tool arm to the left until bevel angle indicator
N1 points to the desired bevel angle
- hold the tool arm in this position and tighten knob N
• Compound cuts $
- compound cuts require both a mitre angle setting and
a bevel angle setting
! always test out first on a piece of scrap material
• Laser line %
- for guiding tool along desired line of cut marked on the
workpiece
- switch on/of laser line by pressing switch P1
- before starting a job, check the alignment of the laser
line with the actual line of cut by making a trial cut on a
piece of waste material
! do not remove or damage warning label A
• Spot light ^
- for accurate tracing of marked line of cut
- switch on/of spot light by pressing switch Q1
• Sawing without slide movement (small workpieces)
- loosen locking knob R in case it is tightened
- slide the tool arm to the stop in the direction of fence L
and retighten locking knob R
- set tool into working position
! ensure that the workpiece is firmly clamped
against the saw table and fence L
- switch on the tool by pulling switch S into handle B and
press safety lever D simultaneously for guiding the tool
arm downward &a
! do not cross your arms when operating the tool
arm &b
- saw through the workpiece with uniform advancing
! the tool should run at full speed before the blade
enters into the workpiece
- switch of the tool by releasing switch S
- wait until the sawblade has come to a complete
standstill before guiding the tool arm slowly upward
• Sawing with slide movement (wide workpieces) *
! be aware that the method described below is the
only safe one
- loosen locking knob R in case it is tightened
! ensure that the workpiece is firmly clamped
against the saw table and fence L
- pull the tool arm away from fence L far enough so that
the saw blade is in front of the workpiece
- switch on the tool by pulling switch S into handle B and
press safety lever D simultaneously for guiding the tool
arm downward &a
! do not cross your arms when operating the tool
arm &b
- push the tool arm in the direction of fence L and saw
through the workpiece with uniform advancing
! the tool should run at full speed before the blade
enters into the workpiece
- switch of the tool by releasing switch S
- wait until the sawblade has come to a complete
standstill before guiding the tool arm slowly upward
• Sawing grooves (
- slide cutting depth limiter T1 to the left
- set the desired depth with depth stop T2 and lock it in
place by tightening nut T3
• Sawing workpieces of the same length )
- loosen knob V1 and position length stop V at the
required distance to the saw blade
- tighten knob V1 again
- position workpiece against length stop V
- saw this and the other workpieces to the same length
• Changing saw blade ¡
! disconnect the plug
- take hex key W from storage W1
- set tool into working position
- push spindle-lock button W2 and hold it while you
loosen blade bolt W3 one turn by turning hex key W
CLOCKWISE (= in same direction as arrow printed on
saw blade)
- release spindle-lock button W2
- press safety lever D 5 and lower the tool arm
somewhat with one hand while lifting lower guard W4
with the other hand
- keep lower guard W4 opened with one hand while
removing blade bolt W3, lange W5 and saw blade
with the other hand
! change saw blade with saw teeth and arrow
printed on saw blade pointing in same direction
as arrow on upper guard W6
- keep lower guard W4 opened with one hand while
mounting lange W5 and blade bolt W3 with the other
hand
- release lower guard W4 and guide the tool arm slowly
upward
- irmly tighten blade bolt W3 by turning hex key W
COUNTER-CLOCKWISE while pushing spindle-lock
button W2
! remove hex key W from blade bolt W3
• Replacing table insert ™
Replace a defective or worn table insert as follows:
! disconnect the plug
- remove all 5 screws as illustrated
- remove old table insert by irst lifting it at the front and
then pulling it out completely
- place new table insert
! firmly tighten all 5 screws
• Checking/adjusting of 90° blade alignment £
! disconnect the plug
- rotate the saw table to the 0° position and lock in place
- lower the tool arm and lock in place
19