ELICA ISOLABELLA Serie Montaje Y Modo De Empleo página 16

normally deactivated. To activate it, see under paragraph
"Activating the carbon filter saturation signal".
First proceed with the maintenance of the filter as
described in the corresponding paragraph.
Press the "+" and "-" keys contemporaneously for about 3
seconds. The LED stops flashing, indicating that the resetting
of the signal has been accomplished.
Deactivating the carbon filter saturation signal (for
special applications)
Switch the hood off (see paragraph above "Selecting the
suction speed (power)").
Press the "◄" key or the "►" key until seeing the symbol
relating to the "Resetting and configuration of the filters
saturation signal" function on the remote control.
Press keys "+" and "-" contemporaneously for about 3
seconds. The LED flashes in GREEN to indicate that the
carbon filter saturation signal has been deactivated.
To reactivate the carbon filter saturation signal, repeat the
operation. The LED flashes in ORANGE.
Maintenance of the remote control
Cleaning the remote control:
Clean the remote control with a damp cloth and a neutral
solution of detergent without abrasive substances.
Changing the battery:
• Open the battery casing using a small screwdriver with a
flat point.
• Change the finished battery with a new one of 12 V type
MN21/23
In inserting the new battery respect the polarity indicated
on the battery casing!
• Close the battery casing up again.
Disposal of the batteries
Ultimate disposal of the batteries should be handled according
to all national laws and regulations. Do not place used
batteries in your regular waste.
Ultimate disposal of the batteries must be done
Contact your local waste management officials for other
information regarding the environmentally sound collection,
recycling, and disposal of the batteries.
Maintenance
Before performing any maintenance operation, isolate the
hood from the electrical supply by switching off at the
connector and removing the connector fuse.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Grease filter
Fig. 11
Traps cooking grease particles.
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
Charcoal filter (filter version only)
Fig. 11
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Replacing lamps
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
To replace the central lamp: use only 40W max 40° D25
GU10.halogen lamps.
Removing the bulb:
rotate anti-clockwise a quarter turn and take out.
Mounting the bulb:
safely.
insert the bulb in its seat so that its contacts enter the
congruent seats on the bulb-holder, rotate clockwise for about
a quarter turn.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
16