RIB K800 Manual Del Usuario página 6

4° Checking manoeuvre direction, force adjustment and slowing down when approaching
WE REPEAT: If the gate opens to the left reverse V and W and LSO with LSC.
Note: In this phase the gate moves only by constantly pressing the PROG button and is the step-by-step type which means that each time the
PROG button is pressed we have an open-stop-close-stop-open ... manoeuvre.
To confirm that the configuration is good check the LEDs as described below.
a) Set the microswitches for K800 DIP 1-2-4-5-6-8-9-11-12-13-14-15-16-17-18 on OFF and DIP 3-7-10 on ON.
for K1400 set DIP 14 ON
for K2200 set DIP 15 ON.
b) Set DIP 1 on ON (the DL1 LED flashes quickly)
c) Set the "TORQUE" force adjustment trimmer on minimum
d) Press and hold the PROG button (the green DL6 LED turns on and the gate opens)
e) Gradually increase "TORQUE" force only if necessary (WARNING: too much force can be dangerous for the users)
f) After 10 seconds the motor slows to a speed that is adjusted with the "LOW SPEED" trimmer.
g) At the end of opening, the limit switch is pressed by the cam and stops the motor (the DL3 and DL6 LEDs turn o ).
h) Release the PROG button.
i) Press and hold the PROG button again (the red DL7 LED turns on and the gate starts closing)
j) After 10 seconds the motor slows down. The limit switch stops the motor when the gate is completely closed (DL4 and DL7 turn o )
k) Release the PROG button and press PROG again to open the gate slightly and free the end-of-closing limit switch.
l) Put DIP 1 back on OFF and go to step 5.
5 - Programming the working and waiting times before having automatic closing.
IMPORTANT: Jumper between COM-PHOT, COM-EDGE and COM-STOP if the safety devices are not installed. LEDs DL2, DL3, DL4, DL5 and DL8
must be on.
If a LED is o it indicates a safety device failure or no connection and gate movement is blocked.
a) Set DIP 2 on ON (the DL1 LED flashes slowly)
b) Press the PROG button briefly (the gate closes, it stops when it comes up against the stop, it waits 2 seconds and then opens automatically,
stopping against the end-of-opening limit switch). Once the gate has completed the opening manoeuvre the control panel starts counting the waiting time before the gate starts closing
automatically.
Note: Even if the automatic closing function is not active (DIP 3 OFF), it must still be memorized.
c) Wait for the length of time wanted and then press the PROG to store the waiting time and start the gate closing.
d) The gate is closed. DL1 stops flashing. The times are stored. Put DIP 2 back on OFF.
6° Programming the remote control (for S1)
SINGLE CHANNEL RECEIVER - Plug either an ACG5055 or ACG5047 radio receiver onto connector J8 (this lets you control the electronic panel directly with the first channel of the remote
control).
Action
1° Press briefly the small button P on the receiver
2° Press key A on the remote control for 1.5 seconds
Let DL2 flash 10 times or press P on the receiver to exit programming
TWO-CHANNEL RECEIVER - Plug either an ACG5051 or ACG5048 radio receiver onto connector J8 (this lets you control the electronic panel directly with the first channel of the remote
control).
Connect the second relay R2 of the radio receiver to COM/PED so the pedestrian opening or other device can be radio controlled.
Action
1° Press briefly the small button P on the receiver
2° Press key A on the remote control for 1.5 seconds
3° Press briefly the small button P on the receiver
4° Press key B on the remote control for 1.5 seconds
Let DL2 flash 10 times or press P on the receiver to exit programming
7° Customising the configuration
The configuration can be modified by moving the various microswitches
Microswitches ON
DIP3 Automatic closing activated
DIP4 Step-by-step RADIO control
DIP5 Step-by-step K BUTT control
DIP6 Photocells active only in closing
DIP7 Encoder activated
DIP8 Pre-flashing for 3 seconds
DIP9 Slowing down not activated
DIP10 Electronic brake activated
DIP11 Gradual start activated
DIP12 Edge monitoring TEST activated
DIP13 S1/R2 or S1/R4 with contactors
DIP17 Reclosing upon passage of the activated photocells
IMPORTANT: The system must comply with all the standards and Directives currently in force.
LED confirm Reaction
DL1 and DL2 flash
DL1 flashes release P
DL2 flashes once does not transmit
LED confirm Reaction
DL1 and DL2 flash
DL1 flashes release P
DL2 flashes once does not transmit
DL2 flashes release P
DL1 flashes once does not transmit
Microswitches OFF
Automatic closing not activated
RADIO control has no e ect in opening
K BUTT control has no e ect in opening
Photocells active all the time
Encoder not activated
Motor and flashing light start together
Slowing down activated
Electronic brake not activated
Gradual start not activated
Edge monitoring TEST not activated
S1
Reclosing upon passage of the non activated photocells
Remarks
go to step 2°
Finished
Remarks
go to step 2°
go to step 3°
go to step 4°
Finished
4
3