Cleaning And Maintenance - UNIPRODO UNI HEATER 02 Manual De Instrucciones

EN
3.1. DEVICE DESCRIPTION
1
10
3 2
11
4
5
9
1
6
8
7
1. Body
2. Display
3. Control panel
4. Air outlet
5. Air outlet protection cover
6. Column
7. Base
8. Power cord
9. ON / OFF switch
10. Handle
11. Air inlet
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C and the relative humidity should be less
than 85%. Ensure good ventilation in the room in which
the device is being used. There should be at least 10
cm distance between each side of the device and the
wall or other objects. Keep the product away from
hot surfaces. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions. Position the
device such that you always have access to the power
plug. The power cord connected to the appliance must
be properly grounded and correspond to the technical
details on the product label.
ASSEMBLING THE DEVICE
1. Assemble the upper (A) and lower (B) parts of the
base as shown in the picture.
A
B
10
2. Fix the device column on the base. Insert the
column into the base's hole and set the body in
such a way that the locating pins go into the holes
in the base. Then secure the base by tightening
the nut on the bottom of the column.
3.3. DEVICE USE
3.3.1. Remote control, control panel, and display
1
A
6
4
B
C
6 5 4 3 2 1
A. Temperature as set
B. Operation mode
C. Graphical representation of the operation mode
1. Standby / exit button
2. Operation mode selection button
3. Button for increasing the value of the parameter
being set (+)
4. Button for decreasing the value of the parameter
being set (-)
5. Timer
6. Rotation button
3.3.2. DEVICE OPERATION
1. Connect the device to the power supply - it will
automatically enter standby mode.
2. To exit the standby mode, press the button (1).
The device will turn on and the display will show
the LO symbol (low heating mode) with the
previously set default temperature for this mode
(during the first start-up, these will be factory
settings).
3. In order to change the operating mode, press
the button (2). The display will show the text
corresponding to the selected mode:
Mode
Description Graphic representation (°C)
(B)
Low
heating
LO
tempera-
ture
High
heating
HI
tempera-
ture
FAN Fan
5
2
3
4. After selecting the LO or HI mode, it is possible
to set the desired temperature. To change the
factory settings, just activate the mode and use
buttons (3) and (4) to set the temperature in the
range from 15 to 45 ° C.
NOTE: After selecting the FAN mode, it is not
possible to set the temperature, only the fan
works and the display shows the ambient
temperature.
5. Additional functions that can be used after
selecting the appropriate operation mode:
• Timer - allows you to set the device operation
time. To do this, press the button (5), the Hr icon
will appear on the display:
Using buttons (3) and (4), set the required time
from 0.5 to 12h and accept the selection by
pressing the button (5) again. After the set time
has elapsed, the device will turn off automatically
and go into standby mode.
• Rotation (6) - after pressing this button the device
will start to rotate sideways by an angle of 45 °
and the display will show the icon:
11 EN
Pressing the button (6) again will disable the
rotation function.
6. To turn off the device, press the button (1) and
remove the plug from the socket.
NOTE: The buttons on the remote control have
the same functions as the buttons on the control
panel. The maximum remote control distance is 3 m.

3.4. CLEANING AND MAINTENANCE

a) Unplug the mains plug and allow the device to
cool completely before each cleaning, adjustment
or if the device is not being used.
b) Always unplug the device before cleaning it.
c) After cleaning the device, all parts should be dried
completely before using it again.
d) Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
e) Do not spray the device with a water jet or
submerge it in water.
f) The device must be regularly inspected to check
its technical efficiency and spot any damage.
g) Use a soft, damp cloth for cleaning (housing, air
outlet cover and base).
h) Do not use sharp and/or metal objects for
cleaning (e.g. a wire brush or a metal spatula)
because they may damage the surface material of
the appliance.
SAFE REMOVAL OF BATTERIES AND RECHARGEABLE
BATTERIES
Remove used batteries from the device using the
same procedure by which you installed them. Recycle
batteries with the appropriate organisation or company.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste
systems. Hand it over to an electric and electrical device
recycling and collection point. Check the symbol on
the product, instruction manual and packaging. The
plastics used to construct the device can be recycled
in accordance with their markings. By choosing to
recycle you are making a significant contribution to the
protection of our environment. Contact local authorities
for information on your local recycling facility.