Petzl B01 TIBLOC Guia De Inicio Rapido página 4

(EN) ENGLISH
Instructions for use
Diagram 1.
Installation on the rope
Attach the TIBLOC to the rope with a locking
carabiner (of round/oval section and diameter
10-12 mm). The TIBLOC is for use on single rope of
diameter between 8 and 11 mm, and of kernmantel
construction (dynamic, semi-static or static) in
conformance with the EN and UIAA standards. For
security, whenever the risk of a fall exists, rope of a
minimum diameter of 10 mm must be used. Respect
the marking which shows which way up the device
must be used, and check that it jams in the desired
direction. A cord leash may be installed to avoid
losing the TIBLOC.
Diagram 2.
Use of the device
A. The pulling force must be applied to the carabiner.
To improve the initial jamming, press on the base
of the TIBLOC with the thumb. Warning, to avoid
slippage of the device which may damage the sheath
of the rope, do not take hold of the TIBLOC directly,
never press on the upper part of the device.
B. To move down the rope, hold the TIBLOC between
three fi ngers to prevent it from jamming.
Precautions
The TIBLOC is an emergency rope clamp/grab for
occasional use. Always check that the device jams
immediately. The rope must always be under tension.
This device is not designed to stop severe falls.
Absorption: remember that the energy of a fall is
absorbed by the rope.
As you approach the anchor point, the capacity of
the rope to absorb impact lessens, and eventually
reaches zero.
Be careful of foreign bodies which can impede the
operation: (pebbles, mud, twigs...).
Diagram 3.
A) Lifting
Before use, check that the TIBLOC swings freely in
the carabiner. Warning, the rope must not only pass
through the TIBLOC, it must also pass through the
carabiner.
B) Free running
C) Simple pulley system
Note that in a pulley system it is always necessary to
check that the TIBLOC has gripped the rope. If not,
this must be done manually. Do not use the TIBLOC in
a hauling system where the rope under tension runs
upwards.
Diagram 4.
Climbing the rope without help from the
structure
You can use two TIBLOCs: one on the harness
and one below on a short footloop which must be
attached to the foot. Step up in the footloop and slide
the chest TIBLOC up the rope. Sit in the harness then
push directly on the lower TIBLOC
to slide it up the rope.
Diagram 5.
Climbing the rope with help from the
structure
Use a lanyard between the harness and the TIBLOC.
4
Notice TIBLOC B01 réf. : B01500 020799
General information
Important notice : specifi c training is
essential before use
Read this notice carefully and keep all product
instructions and information. Only the techniques
shown in the diagrams that are not crossed out are
authorised. All other uses are excluded : danger
of death. A few examples of misuse and forbidden
uses are also represented (shown in the crossed out
diagrams or with the "skull and crossbones" symbol).
Many other types of misuse exist and it is impossible
to enumerate or even imagine all of them. In case of
doubt or diffi culty in understanding, contact PETZL.
Activities at height are dangerous and may lead to
severe injury or even death. Gaining an adequate
apprenticeship in appropriate techniques and
methods of protection is your own responsibility.
You personally assume all risks and responsibilities
for all damage, injury or death which may occur
during or following incorrect use of our products in
any manner whatsoever. If you are not able, or not in
a position to assume this responsibility or to take this
risk, do not use this equipment.
Use
This product must only be used by competent and
responsible persons, or those placed under the direct
and visual control of a competent and responsible
person.
Personal protective equipment (PPE) is to be used
only on or with energy absorbing systems (for
example dynamic ropes, energy absorbers etc...).
Check that this product is compatible with the other
components of your equipment (see the instructions
specifi c to this product).
To prolong the life of this product, care is necessary,
when transporting as well as when using it. Avoid
impacts, or rubbing against abrasive surfaces or
sharp edges.
It is up to the user to foresee situations requiring
rescue in case of diffi culties encountered while using
this product.
Checking = safety
Do not hesitate to scrap a product showing signs of
wear which might affect its strength, or restrict its
operation. For your safety we advise you to adopt a
3-level checking schedule :
- before and after each use it is necessary to check
the condition of the product,
- during use, it is important to regularly monitor the
condition of the product and of its connections to the
other elements of the system.
- Periodically, a more thorough inspection must be
carried out by a competent inspector : approximately
every three months for textile products and helmets,
approximately annually for metallic products.
For more safety and better control of your equipment,
we advise you to keep an inspection record for each
product.
It is preferable to personally issue each user of P.P.E.
with his or her own set of equipment.
Major fall and impact
Do not continue to use this product after a major fall
or a major impact (fall of the product or impact on
the product). Even though no external signs may be
visible, a deformation may restrict its operation or
internal damage may have occurred, thus reducing
its strength. Do not hesitate to contact PETZL in case
of doubt.
Lifetime = shelf life + useful life
Shelf life (in favorable conditions) :
Helmets, harnesses, webbing slings and
lanyards : 5 years
Metallic products: no limitation.
- The useful life depends on the intensity and the
environment of usage. Certain environmental
elements will considerably accelerate wear : salt,
sand, snow, ice, moisture, chemicals. In exceptional
circumstances, wear or damage could occur on the
fi rst use which reduces the lifetime of the product to
that one single use.
Maximum useful life: helmets, harnesses : 5 years;
slings, lanyards : 3 years;
metallic products : no limitation.
For webbing, slings, and lanyards, because of their
direct contact with supporting structures and the
heavy demands that usage places on them, their
average operational lifetime is 6 months heavy use,
12 months normal use, 3 years maximum occasional
use.
PETZL guarantee
This product is guaranteed for 3 years against any
faults in materials or manufacture. Exclusions from
the guarantee: normal wear and tear, modifi cations
or alterations, incorrect storage, poor maintenance,
damage due to accidents, to negligence, or to
improper or incorrect usage.
Responsibility
PETZL is not responsible for the consequences,
direct, indirect or accidental, or any other type of
damage befalling or resulting from the use of its
products.