Flo 79890 Manual De Instrucciones página 10

Head high
[m]
0
1
2
3
4
5
6
7
8
9
10
11
Attention! In order to ensure the maximum efficiency of the appliance, connect to the pump a hose whose diameter corresponds
to the maximum diameter of the water connection.
GENERAL SAFETY CONDITIONS
NOTE! Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, fire or injuries. The
notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and
wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean. Disorder and poor illumination may be a cause of accidents. Do
not work with electric tools in explosive environments, or those which contain inflammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a fire in case of contact with inflammable gases or vapours. Do not allow
children and outsiders to the place of work. A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must fit the mains socket. Do not modify the plug. Do not use any adapters whatsoever
in order to adapt the plug to the socket. Unmodified plug which fits the socket reduces the risk of an electric shock. Avoid
contact with grounded surfaces, such as pipes, heaters and refrigerators. Grounding of the body increases the risk of an
electric shock. Do not expose electric tools to precipitation or humidity. Water and humidity which gets into the electric tool
increases the risk of an electric shock. Do not overload the power supply cable. Do not use the power supply cable in order
to carry the tool or to connect and disconnect the plug from the mains socket. Avoid contact of the power supply cable
with heat, oils, sharp tools and moving elements. Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside
closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you
are tired or under effects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries. Avoid accidental activation of
the tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with a finger
on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries. Before you turn an
electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating
elements of the tool may lead to serious injuries. Keep your balance. Maintain an appropriate position. It will permit to control
the electric tool in case of unpredicted situations during its operation. Use protective clothes. Do not wear loose clothes or
jewellery. Keep your hair, clothes and gloves away from moving elements of the electric tool. Loose clothes, jewellery or
long hair may get caught on moving elements of the tool. Use dust extractors or dust containers, if the tool is equipped with
any. Make sure they are properly connected. Using of dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work
will result in a more efficient and safer work. Do not use the electric tool if the switch is not functioning properly. A tool which
may not be controlled by means of a switch is dangerous and must be repaired. Disconnect the plug from the mains socket
O P
10
79890 79891 79892
7500 10500 13000
6000 9500 12000
5000 8500 11500
4000 7500 10500
3000 7000 9500
1000 5500 8000
- 3500 6500
- 1000 4500
- - 2500
- - 1000
- - -
- - -
E R A T I
GB
Pump type
79893 79894 79896
Capacity [dm /h]
3
14000 15000 12500
13500 14000 12000
12500 13500 11500
11500 12500 10500
10500 11500 9500
9500 10500 8000
8000 9500 6500
6500 8000 3500
4000 5500 1000
2500 3500
1000 2000
- 500
N G M A
79897 79898
13000 14500
12000 13500
11500 12500
10500 11500
9500 10500
8000 9500
6500 8000
3500 6500
2000 4000
- 1000 3500
- - 1000
- - -
N U A L
79899
15500
14000
13500
12500
11500
10500
9500
8000
5500
3500
2000
500