Operating Conditions - Flo 79890 Manual De Instrucciones

GB
before any adjustment, replacement of accessories or storage of the tool. It will permit to avoid accidental activation of the
electric tool. Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be
dangerous in hands of an untrained person. Make sure the tool is properly maintained. Check the tool in order to detects
any unfitting or loose moving elements. Check whether the elements of the tool are not damaged. In case any damaged
elements of the tool are detected, they must be repaired before the electric tool is operated. Many accidents are caused
by improper maintenance of tools. Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to
control during work. Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool
in accordance with its purpose, taking into account the kind and conditions of work. Should the tool be used for other
applications than the ones it has been designed for, the risk of a dangerous situation increases.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee
a proper level of safety of operation of the electric tool.

OPERATING CONDITIONS

Under no circumstances is it allowed to operate a pump with a damaged connection cord or plug. In case any such damage
is detected, they must be replaced with new ones by authorised personnel, and after replacement it is required to carry out
measurements of the efficiency of the anti-electric shock protection.
The pump must be connected to the 230V/50Hz AC mains with neutral earthing and a circuit protection of a minimum rating
amounting to 6A.
Do not use the pump in swimming pools.
If the pump is installed in water reservoirs to which people or animals may have access, e.g. garden ponds, or within their
protection areas, then the power supply circuit must be equipped with a residual current device whose minimum rated current
must be 6A and the maximum differential current must not exceed 30mA.
The pump must not be functioning or be connected to the mains, when in the reservoir in which it is meant to be used are people
or animals.
The surroundings of the basket of the pump must be clean, so as to avoid any blockage of the inlet suction conduits.
During the operation the upper surface of the pump must be submerged at least 7 cm below the surface of water. If the water level
drops below this value, then the float switch automatically deactivates the device.
The pump may be hanged only by the holder provided for this purpose.
The pump may remain on the bottom of the reservoir, provided it is on a flat surface.
If the pump is being operated in a well, the minimum dimensions of the well must be (40 x 40 x 50) cm.
Before any maintenance or current service of the pump, it is required to remove the plug of the cable of the pump from the mains
socket.
The device must not be operated by children or persons whose physical, sensorial and psychological capacities are reduced, or by persons lacking the required experience and knowledge, unless they are supervised or have been trained. Supervise children
and make sure they do not use the device as a toy.
RECOMMENDATIONS FOR OPERATION
The pump may be cleaned solely with a jet of clean water.
In case of permanent installation, it is required to check the operation of the float switch at least once in three months. Adjustments
of the points of activation of the float switch must be carried out changing the free length of its cable. In order to do so, move the
cable connecting the pump with the switch in the clamping slot at the side of the body of the device to a position, in which the
condition of the minimum submersion of the pump below the water surface is fulfilled.
The free length of the cable must not be too low, since this would imply a risk of incorrect operation (e.g. dry running), and
consequently the danger of damage to the pump.
MAINTENANCE AND OVERHAUL
ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the operations have been
finished, the technical conditions of the tool must be assessed by means of external evaluation and inspection of the following
elements: body and handle, conductor with a plug and deflection, functioning of the electric switch, patency of ventilation slots,
sparking of brushes, noise level of functioning of bearings and gears, start-up and smoothness of operation. During the guarantee
period, the user cannot dismantle the electric tools or change any sub-assemblies or elements, since it will cancel any guarantee
rights. All irregularities detected at overhaul or during functioning of the tools are a signal to have the tool repaired at a service
shop. Once the functioning has been concluded, the casing, ventilation slots, switches, additional handle and protections must be
cleansed with a stream of air (at a pressure not exceeding 0.3 MPa), with a brush or a cloth without any chemical substances or
cleaning liquids. Tools and handles must be cleansed with a clean cloth.
O P E R A T I N G M A N U A L
11