How To Operate The Unit - Makita DCF300 Manual De Instrucciones

WARNING
• Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient
to inflict serious injury.
WARNING
• Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attach-
ments or accessories not recommended can result in serious personal injury.
This fan is equipped with a 3-speed control using the speed switch; you can also set run time for 1 hour, 2 hours, or 4
hours. Power supply can be with AC adaptor or battery cartridge (Optional accessory).
USING AC ADAPTOR (Fig. B & C)
Insert the 1V DC plug (1 in Fig. C) of AC adaptor into the 1V DC socket (1 in Fig. B), and then plug the AC pins
(1 in Fig. C) into a main power supply. Make sure that the voltage rating of the main power supply corresponds with
that of the adaptor.
To operate the cordless fan, first you need push the power switch button
fan starts to work on high speed mode
change button ( in Fig. A-1) and the speed indicator will show on middle
Push the power switch button
from the main power supply, and allow the cordless fan to cool completely before performing any inspection, mainte-
nance, cleaning procedures or storage.
OSCILLATING CONTROL
The oscillating control switch
for oscillation and press it again for stationary.
The oscillating angle is as shown in Fig. D.
HEAD ADJUSTMENT
To adjust the direction of the fan, hold the front of the fan head with both hands, and gently push it to the desired
position.
The angle is adjustable by every 15 degrees between the range illustrated in Fig. E.
USING BATTERY CARTRIDGE
IN ORDER TO ENSURE THE BATTERY MAXIMUM PERFORMACE, IT IS RECOMMENDED THAT THE BATTERY
CARTRIDGE SHOULD BE CHARGED BEFORE BEING USED FOR THE FIRST TIME.
1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, () battery, and
() product using battery.
. Do not disassemble battery cartridge.
. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating,
possible burns or even an explosion.
. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result
in loss of your eyesight.
. Do not shorten the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
() Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 0°C (1°F).
7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery car-
tridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS
Tips for maintaining maximum battery life:
1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery
cartridge when you notice less tool power.
. Charge the battery cartridge with room temperature at 10°C – 0°C (0°F – 10°F). Let a hot battery cartridge cool
down before charging it.
. Charge the battery cartridge once in every six months if you do not use it for a long period of time.
. Cover the battery cover when not use.
6

HOW TO OPERATE THE UNIT

. If you want to change to middle
(8 in Fig. A-1) to turn off the unit after you finish using, then unplugged the AC adaptor
(9 in Fig. A-1) is used to choose oscillation or stationary mode. Press the switch down
(8 in Fig. A-1) to turn on the fan, now the
or low speed mode, push the speed
or low speed mode.