Usb Power Port; Troubleshooting - Black+Decker PPRH5B Manual De Instrucciones

4. Make sure the combined rating for all appliances plugged into the unit is 500 watts or lower and that
appliance cord(s) and plug(s) are not damaged.
5. Assure there is adequate ventilation around the unit before proceeding.
12 VOLT DC PORTABLE POWER SUPPLY
The 12 volt DC accessory outlet is located under a protective cover on the right hand side of the front panel
(refer to the Features section to locate). This portable power source is for use with all 12 volt DC accessories
equipped with a male accessory outlet plug that are rated up to 5 amps.
1. Lift up the cover of the unit 's 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT EXCEED
A 5 AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically check the unit's battery status by pressing the battery power level button. (Two red and one
green battery status indicator lights indicate a full battery. Only one red battery status indicator lights
indicates that the unit needs to be recharged.)

USB POWER PORT

The USB power port is under the same protective cover as the 12 volt DC outlet at the left hand side of the front
panel (refer to the Features section to locate).
1. Push the USB Power Button to turn the USB Port on and the USB power indicator will light.
2. Lift up the cover of the USB Charging Port.
3. Plug the USB-powered device into the USB Charging Port and operate normally.
4. Periodically check the unit's battery status by pressing the battery power level button. (Two red and one
green battery status indicator lights indicate a full battery. Only one red battery status indicator lights
indicates that the unit needs to be recharged.)
Notes:
This unit's USB charging port does not support data communication. It only provides 5 volts/2,000 mA DC power to an external USB-
powered device.
Some USB-powered household electronics may not operate with this USB charging/power port. Check the manual of the
corresponding electronic device to confirm that it can be used with this type of USB charging/power port.
Make sure the USB power button is turned off when the unit is being recharged or stored.
AREA LIGHT
The built-in 3-LED area light located on the back of the unit is controlled by the area light power button on the
front panel (refer to the Features section to locate). Press the area light on/off button once to turn the light on.
Press the area light power button again to turn the area light off.
Periodically check the unit's battery status by pressing the battery power level button. (Two red and one green
battery status indicator lights indicate a full battery. Only one red battery status indicator lights indicates that the
unit needs to be recharged.)
Note:
Make sure the area light and the unit are turned off when the unit is being recharged or stored.
PORTABLE COMPRESSOR
The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational
inflatables. The compressor hose with SureFit ® nozzle is stored in the compressor hose storage compartment.
The compressor on/off switch is located on the front panel of the unit to the right of the air pressure gage (refer
to the Features section to locate). The compressor can operate long enough to fill up to 3 average sized tires
before the battery must be recharged.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting the nozzle
adapter to the air hose. Return the hose to the storage compartment after use.
WARNING – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: follow all safety
instructions found in the "Specific Safety Instructions for Compressors" section of this instruction
manual.
Inflating Tires or Products With Valve Stems
1. Screw the SureFit nozzle onto the valve stem. Do not overtighten.
®
2. Turn on the compressor power switch.
3. Check pressure with the pressure gauge.
PPRH5B_ManualENSP_082018.indd 10-11
10
4. When desired pressure is reached, turn off the compressor power switch.
5. Unscrew and remove the SureFit nozzle from the valve stem.
®
6. Allow the unit to cool, then recharge before storing away.
7. Store the compressor hose and nozzle in the storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of the nozzle adapter.
1. Screw the nozzle adapter into the SureFit nozzle. Do not overtighten.
®
2. Insert the adapter into item to be inflated.
3. Turn on the compressor power switch – inflate to desired pressure or fullness.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
4. When desired pressure or fullness is reached, turn off the Compressor Power Switch.
5. Disconnect the nozzle adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the SureFit
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, nozzle and nozzle adapter in the storage compartment.

TROUBLESHOOTING

Problem Solution
Unit will not charge • Make sure the inverter power switch is in the off position.
• Make sure a suitable gage extension cord is properly connected to both
the unit and a functioning AC outlet.
• Make sure the 12 volt DC charger is properly connected to both the unit
and a functioning DC power source.
Unit fails to jump-start • Make sure unit's jump-starter power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
120 volt AC outlet will not power
• Make sure the inverter power switch is in the on position.
appliance
• Make sure you have followed all the steps in the 120 AC portable
power supply instructions carefully. Refer to the important notes
included in that section that explain common problems and solutions.
• Check that unit has a full charge. Recharge unit if necessary.
12 volt DC accessory outlet will
• Make sure the the appliance does not draw more than 5 amps.
not power appliance
• Check that unit has a full charge. Recharge unit if necessary.
USB power port will not power
• Make sure the USB power button is in the on position.
appliance
• Make sure the appliance being powered does not draw more than
2,000mA.
• Some USB-powered household electronics may not operate with this
USB charging/power port. Check the manual of the corresponding
electronic device to confirm that it can be used with this type of USB
charging/power port.
• Check that unit has a full charge. Recharge unit if necessary.
LED area light does not come on • Make sure the area light power button is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
nozzle.
®
or
11
8/20/2018 6:10:12 PM