Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3. Charge the unit until the green FULL indicator lights when the Battery Power Level Button is pressed (with
the adapter unplugged from the unit). DO NOT CHARGE MORE THAN 6 HOURS MAXIMUM USING THIS
METHOD.
4. When charging is complete, remove the charging cord and store in a safe place.
Notes:
Some vehicles require that the ignition be switched to the accessory outlet position in order to power the accessory outlet.
Do not leave the unit unattended when charging using the this method.
JUMP-STARTER
This Jump-Starter is equipped with an On/Off Power Switch. Once the connections are properly made, turn the
switch on to jump-start the vehicle.
1. Turn off vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place
vehicle in "park" and set the emergency brake.
2. Make sure the Jump-Starter Power Switch is turned to off.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is
connected to chassis) (MOST COMMON)
4a. Connect positive (+) red clamp to vehicle battery's positive terminal.
4b. Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body
part. Never clamp directly to negative battery terminal or moving part. Refer to the automobile owner's
manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
Notes:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to
chassis), replace steps 4a and 4b above with steps 5a and 5b, then proceed to step 6.
5a. Connect negative (–) black clamp to vehicle battery's negative terminal.
5b. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or
body part. Never clamp directly to Positive battery terminal or moving part. Refer to the automobile
owner's manual.
6. When clamps are connected properly, turn the Jump-Starter Power Switch to ON.
7. Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts.
8. Turn the Jump-Starter Power Switch back to the OFF position.
9. Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THE "SPECIFIC SAFETY INSTRUCTIONS FOR JUMP
STARTERS" SECTION OF THIS INSTRUCTION MANUAL.
• This power system is to be used ONLY on vehicles with 12-volt DC battery systems.
• Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or
explosion.
• Always turn the unit off when not in use.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before
jump-starting this type of vehicle, read the vehicle manual to confirm that external-starting assistance is
advised.
• Excessive engine cranking can damage the vehicle's starter motor. If the engine fails to start after the
recommended number of attempts, discontinue jump-start procedure and look for other problems that need to
be corrected.
• If the connections to the battery's positive and negative terminals are incorrect, the reverse polarity indicator
will light and the unit will sound a continuous alarm until the clamps are disconnected. Disconnect clamps and
reconnect to battery with correct polarity.
• If vehicle fails to start, turn off the ignition, turn off the jump-starter power switch, disconnect the jump-start
system's leads and contact a qualified technician to investigate why the engine did not start.
• Recharge this unit fully after each use.
PPRH5B_ManualENSP_082018.indd 8-9
8
120 VOLT AC PORTABLE POWER SUPPLY
Rated Versus Actual Current Draw of Equipment
Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the
power consumption in amps or watts. Be sure that the power consumption of the item to be operated is below
500 watts. If the power consumption is rated in amps AC, simply multiply by the AC volts (120) to determine
the wattage.
Resistive loads are the easiest for this unit to run; however, it will not run larger resistive loads (such as electric
stoves, coffee pots and heaters), which require far more wattage than the unit can deliver on a continuous basis.
Inductive loads (such as TVs and stereos) require more current to operate than do resistive loads of the same
wattage rating.
CAUTION: RECHARGEABLE DEVICES
• Certain rechargeable devices are designed to be charged by plugging them directly into an AC receptacle.
These devices may damage the inverter or the charging circuit.
• When using a rechargeable device, monitor its temperature for the initial ten minutes of use to determine if it
produces excessive heat.
• If excessive heat is produced, this indicates the device should not be used with this inverter.
• This problem does not occur with most of the battery-operated equipment. Most of these devices use a
separate charger or transformer that is plugged into an AC receptacle.
• The inverter is capable of running most chargers and transformers.
Power Inverter Output Waveform
The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that has
characteristics similar to the sine wave shape of utility power. This type of waveform is suitable for most AC
loads, including linear and switching power supplies used in electronic equipment, transformers, and small
motors.
Using the Dual 120 Volt AC Outlets
The two 120 volt AC outlets each are located under a protective cover on the left hand side of the front panel
(refer to the Features section to locate). The two outlets support a combined maximum power draw of 500 watts.
1. Press the inverter power switch to turn the inverter on (I). The inverter power indicator will light red to
indicate the two 120 volt AC outlets are ready to use.
2. Lift up the cover of one of the 120 volt AC outlets.
3. Insert the 120 volt AC plug from the appliance into the 120 volt AC outlet.
4. Switch on the appliance and operate as usual.
5. Periodically check the unit's battery status by pressing the battery power level button. (Two red and one
green battery status indicator lights indicate a full battery. Only one red battery status indicator lights
indicates that the unit needs to be recharged.)
Notes:
Some laptop computers may not operate with this inverter.
Make sure the inverter power switch is turned off when the unit is being recharged or stored.
Protective Features
The inverter monitors the following conditions:
Low internal battery voltage: The inverter will automatically shut down when the battery voltage drops too
low, as this can harm the battery.
High internal battery voltage: The inverter will automatically shut down when the battery voltage is too high,
as this can harm the unit.
Thermal shutdown protection: The inverter will automatically shut down when the unit becomes overheated.
Overload/short circuit protection: The inverter will automatically shut down when an overload or short circuit
occurs.
IMPORTANT NOTES: The inverter power indicator will flash red to indicate that one of the above fault
conditions is present before automatic shutdown occurs. Should this occur, take the following steps:
1. Disconnect all appliances from the unit.
2. Press the inverter power switch to turn the inverter off (O).
3. Allow the unit to cool down for several minutes.
9
8/20/2018 6:10:12 PM
Tabla de contenido
