Suzuki 990D0-04K55-CRB Instrucciones De Montaje

®
Carbon meter visor - matt finish
Description:
Applications: GSX-S1000 AL6
Ref. Description
Part List
Carbon meter visor
1
Cushion
2
Bracket, LH
3
Bracket, RH
4
Spacer
5
Screw (M5x16mm)
6
Screw (M5x20mm)
7
Screw (M5x30mm)
8
Rubbernut
9
Washer, Rubber
AT
Washer, Nylon
AK
Washer
AL
Mounting instructions
AM
Ref. Description
Tools Required
1 Hex Bit Socket (3mm / 4 mm)
2 Extension
Ratchet
3
4 Screw Driver (PH2)
5 Drill Bit (φ9.6mm)
6 Electric Drill
7 Ruler
Torque Wrench
8
! WARNING /  ! CAUTION / NOTICE / NOTE. 
Important
Please read this manual and follow its instructions carefully. To emphasize special
information, the symbol 
have special meanings. Pay particular attention to messages highlighted by these
signal words:
Indicates a potential hazard that could result in death or serious injury.
Indicates a potential hazard that could result in minor or moderate injury.
Indicates a potential hazard that could result in vehicle or equipment damage.
NOTE: indicates special information to make maintenance easier or instructions
clearer.
1 SUZUKI Deutschland GmbH, Suzuki-Allee 7, D-64625 Bensheim
MOUNTING INSTRUCTIONS
990D0-04K55-CRB
Part Number:
Mounting Time:
Qty.
1
1
1
1
3
1
2
5
2
2
7
2
4
9
4
2
AK
2
AL
1
1
3
5
7
! and the words WARNING, CAUTION, NOTICE and NOTE
WARNING
!
CAUTION
!
NOTICE
1. Check that the kit includes all the parts listed on the first page.
Precautions for
2. Check each part in the kit for scratches or any form of damage.
Installation
3. Park the vehicle on level ground.
30 Min
4. Remove the ignition key from the switch and store it in a safe place.
5. Protect any items removed or to be installed from scratches by placing them on a
soft cloth first before putting them on the ground.
6. Use care not to cause any damage to the body of the vehicle during installation
2
of the accessory.
4
6
Tighten bolts to the torque indicated in the right
Tightening
8
table as standard value unless otherwise explicitly
Torque
specified. The value shows conventional or "4"
AT
marked bolt tightening torque. For other bolts not
listed in the table, refer to the service manual.
AM
NOTE: Read these instructions carefully before assembly and examine
Mounting
whether all parts are enclosed in accordance with the parts list.
2
1. Apply cushion 2 in the backside of carbon meter visor 1. (Fig 1)
2. Remove meter cover (A), headlamp cover (B),headlamp upper cover (C) and headlamp (D)
4
according to the service manual. (Fig 2)
Note: pay attention not to brake the connecting clip upon removing headlamp cover (B) and
6
headlamp upper cover (c).
8 3. Drill 2 holes with electric drill along the marked area in the back side of headlamp upper cover (C)
(φ9.6mm). (Fig 3)
4. Remount meter cover (A), headlamp cover (B), headlamp upper cover (C) and headlamp (D) to the
body.
5. Install bracket,LH 3 and bracket,RH
5, screw (M5x16mm) 6, rubbernut
6. Install carbon meter visor 1 to bracket,LH 3, bracket,RH 4 and meter cover (A), using screw
(M5x20mm) 7, screw (M5x30mm) 8, rubbernut 9, washer, rubber AT , washer, nylon
washer AL. (Fig 5)
Note: check the tightening torque of each bolt on a regular basis and tighten as needed.
To clean, rinse carbon part with water to remove grit and soften dirt. Use a mild non-
Care and
abrasive liquid soap, plenty of warm water, and a clean flannel cloth or soft chamois.
Maintenance
Rinse well to remove all soap residue. Pat dry do not wipe.
Due to mounted SUZUKI Genuine Accessories the service and maintenance flat rate
Inspection
might be affected. Dismounting/Mounting of SUZUKI Genuine Accessories is
possibly necessary for service and maintenance.
The holder of the vehicle should always be in possession of the mounting instruction.
CAUTION
!
If you do not feel technical qualified to install this product on your own,
please consult with your nearest SUZUKI dealer.
to meter cover (A) and headlamp upper cover (C), using spacer
4
and washer, rubber AT. (Fig 4)
9
CAUTION
!
In case of fall, check all screws and parts. Check also the tightness.
If necessary replace screws or damaged parts.
SUZUKI GENUINE ACCESSORIES
Diameter Tightening Torque
(mm)
N·m kgf-m lbf-ft
5 3.0 0.3 2.2
6 5.5 0.55 4.0
8 13.0 1.3 9.5
10 29.0 2.9 21.0
and
AK
09/2015 ENG