CREE LIGHTING RUL-B Serie Guia De Inicio Rapido

IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l'alimentation avant l'installation.
2. This luminaire must be installed in accordance with the NEC or your
local electrical code. If you are not familiar with these codes and
requirements, consult a qualified electrician.
Ce produit doit être installé conformément à NEC ou votre code
électrique local. Si vous n'êtes pas familier avec ces codes et ces
exigences, veuillez contacter un électricien qualifié.
3. Suitable for wet locations.
Convient aux emplacements mouilles.
4. Min. 75C supply conductors.
Les fils d'alimentation doivent convenir pour 75C.
5. Suitable for operation in ambient not exceeding 40°C.
Peut etre utilise a une temperature ambiante n'excedant pas 40°C.
6. If mounting bolts are completely removed in the field they should
be hand threaded (prior to use of power tools) to ensure proper
engagement of the thread when re-installing. Failure to pre-start
threads may result in cross-threading or stripping of the bolts during
reinstallation.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
TO INSTALL:
1
D-ring Screw
LUMINAIRE INSTALLATION
STEP 1:
To open cover, unscrew the D-ring by hand. See
STEP 2:
If luminaire is being mounted on a 1.66" O.D. pole tenon or mast arm,
proceed to Step 3.
If luminaire is being mounted on a 2.38" O.D. pole tenon or mast arm,
mounting bracket must be flipped. To flip mounting bracket, remove (2)
mounting bracket bolts and (2) washers on each bolt. See Figure 2. Flip
bracket over and loosely reinstall bolts and washers. See Figure 3.
NOTE: Lock washers should be placed on bolt first followed by flat
washers.
1 of 2
Mounting Bracket
2
Bolts and Washers
Figure 1.
NOTES:
• For use with 120-277 VAC.
• Nema receptacle has orientation stops incorporated to
®
prevent greater than 360º rotation. Do not force beyond to avoid
damages in the receptacle and/or in the electrical connections
inside the luminaire.
• Prior to installation, store luminaire in a dry location protected
from rain, dust, and outdoor environment. If equipped with a
photocell receptacle, do not store or install luminaire outdoors
without immediately installing a suitable photocell, shorting
cap, or other compatible device. Do NOT leave receptacle open
to environmental elements. Luminaires with a top-mounted
photocell receptacle should not be installed in an up-light
position or at a tilt greater than 45 degrees from the down-light
position.
3
Mounting Bracket
STEP 3:
Slide fixture on to pole tenon or mast arm through opening on the rear
Figure 2.
of housing. See
STEP 4:
Adjust leveling of fixture from side to side. To level from front to back,
slide pole to different Adjustment Steps in housing. Each step changes
the angle in 2.5° degree increments. See
STEP 5:
Once desired position is achieved, use 9/16" socket wrench to tighten
mounting bolts to 240 in-lbs torque See
RUL-B Series
LED Rural Utility Luminaire
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D'INSTALLATION
NOTE: Side Of Bracket With
Large Offset Facing Away
From Luminaire for use with
2.38" O.D. tenon or mast arm.
Bracket flipped
into proper
orientation for
use with 2.38"
O.D. tenon or
mast arm
Figure 4 on the back page.
Figure 2
.
LPN00847X0001A0_A