Skil 0520 Manual Original página 6

SKIL_IB0520v2 07-01-2009
- use a target surface of at least 3 x 3 m, when
measuring long distances (12 - 15 m)
- ensure that no other ultrasonic sources are in the
vicinity
- when measuring through door en window openings,
ensure a correct result by measuring from two or
three different positions and compare the results
- the ultrasonic waves do not penetrate glass/windows
- in case of severe temperature changes, allow the tool
to adjust to the ambient temperature for half an hour
before starting new measurements
- fluctuations in air pressure and humidity, wind noise
and other sources of noise may lead to faulty
measurements
Single measurement 8
- press button F 3
- aim the tool towards the target surface
- press "Read" button; measurement appears on top
line of display
- measurement is repeated continuously until "Read"
button is released (ticking sound)
- each new single measurement erases the previous
one
Multiple measurement 9
- press button H 3
- aim the tool towards the first target surface
- press "Read" button; first measurement appears on
top line of display
- aim the tool towards the second target surface
- press "Read" button; second measurement appears
on top line of display (small figure 2 appears in upper
right corner of display and sum of two measurements
appears on bottom line of display)
- in the multiple measuring mode a maximum of
10 measurements can be added
- the small figure in upper right corner of display
indicates the measurement number (1 - 10)
- press button H 3 again for starting a completely new
multiple measurement
Surface measurement 0
- press button G 3 once
- aim the tool towards the first target surface (length)
- press "Read" button; measured length appears on top
line of display
- aim the tool towards the second target surface
(width)
- press "Read" button again; measured width appears
on top line of display while calculated surface
appears on bottom line of display
- press button G 3 twice for starting a completely new
surface measurement
Volume measurement !
- press button G 3 twice
- aim the tool towards the first target surface (length)
- press "Read" button; measured length appears on top
line of display
- aim the tool towards the second target surface
(width)
14:34 Pagina 6
- press "Read" button again; measured width appears
- aim the tool towards the third target surface (height)
- press "Read" button again; measured height appears
- press button G 3 twice for starting a completely new
Recall of previous measurements
Press "Recall" button for reviewing previous
measurements, starting with the last measured distance
(10 at the maximum)
Correction of multiple measurement
- press "Recall" button; last measurement and
- press "Recall" more often until measurement to be
- press "Clear" button; measurement is replaced by 0
- aim the tool towards target surface for new
- press "Read" button; new measurement replaces 0
- for continuing multiple measurement, press "Read"
- corrections are possible for 10 previous
Correction of surface/volume measurement
- press "Recall" button; last measurement and
- press "Recall" more often until measurement to be
- press "Clear" button; measurement is replaced by 0
- aim the tool towards target surface for new
- press "Read" button; new measurement replaces 0
- press "Read" button again for continuing
Faulty measurement
- when the measurement is unsuccessful, symbol @
- press "Read" button or restart the tool
Belt bag for easy and convenient storage #
MAINTENANCE
Do not expose the tool to continuous vibration or
extremely hot or cold temperatures
Always store the tool indoors in its protective
carton/case
Always keep the tool free of dust, moisture and direct
sunlight
6
on top line of display while calculated surface
appears on bottom line of display
on top line of display while calculated volume appears
on bottom line of display
volume measurement
corresponding small figure starts to blink
corrected is found
and sum of remaining values appears on bottom line
of display
measurement
and new value is added to the sum
button again and small figure jumps to next empty
memory place
measurements at the maximum
corresponding line of length/width/height starts to
blink
corrected is found
and recalculated value appears on bottom line of
display
measurement
and value on bottom line of display is recalculated
again
surface/volume measurement
appears on display