English; Safety Warnings - Hydor AQAMAI KP Guía De Usuario

ENGLISH

SAFETY WARNINGS

DANGER
- To avoid possible electric shock, special care should be taken in the
use of aquarium equipment. For each of the following situations, do not
attempt repairs yourself; for assistance or to dispose of the device, return
it to an authorised service centre.
- The appliance is not to be used by children or people with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
- Never run the pump out of water, do NOT run dry, the heat buildup may
cause damage to its components.
- Always unplug with dry hands for any maintenance or service.
- AQAMAI pumps are 12VDC. Please ensure you use only the AQAMAI
power supply.
- Ensure AQAMAI 12VDC power supply is plugged into an outlet with a
drip loop (fig. 3).
- Avoid the possibility of the appliance plug, power supply or wireless hub
from getting wet. Mount in aquarium stand where there is no possibility of
water dripping onto them. For any wires for aquarium devices connected
to electrical mains, the user must ensure that a "drip-loop" is created. A
"drip-loop" is that part of the cord below the level of the receptacle, or the
connector if an extension cord is used, to prevent water traveling along
the cord and coming in contact with the appliance.
- Turn controller OFF and disconnect the pump from power before
performing any service.
- Ensure AQAMAI pumps and any accessories all have a drip loop installed
before plugging into the outlet.
- Only use in freshwater or saltwater applications, do not use pumps in
other liquids.
- The AQAMAI pump utilizes very powerful magnets and can cause severe
personal injury.
- This product carries a water ingress protection rating of IPX2 and
the only portion that can be fully immersed in water is the pump. If the
controller falls into the water, DON'T reach for it! First unplug it and then
retrieve it. If electrical components of the controller get wet, unplug the
controller immediately (Non- immersible equipment only).
- Carefully examine the appliance after installation. It should not be
plugged in if there is water on parts not intended to be wet.
- Do not operate any appliance if it has a damaged cord or plug, or if it
is malfunctioning or if it is dropped or damaged in any manner. Inspect
power cord insulation to be sure there are no cuts or exposed wire. If
so, Customer service would need to verify pump failure prior to warranty
work.
- Always unplug an appliance from an outlet and battery backup when not
in use, before putting on or taking off parts, and before cleaning.
- Never yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect.
- Do not use an appliance for other than intended use. The use of
attachments is not recommended, and will invalidate any warranty.
- Make sure an appliance mounted on a tank is securely installed before
operating it. Read and observe all the important notices on the appliance.
- To avoid injury, do not contact moving parts or hot parts such as heaters,
reflectors, lamp bulbs, etc.
4
IMPORTANT
Before installation, read all safety instructions & warnings.
WHAT'S INCLUDED - fig.1
ITEM DESCRIPTION
A
B
C
Power supply
D Power cord *
E Adhesive cable clips
F
Self tapping screw
G Cable protector
PUMP POSITIONING
1. Once you have chosen the location where you wish to install your
AQAMAI pump, clean away any dirt, calcium deposits and algae (coralline
or otherwise) using an aquarium scraper or scrubber.
2. Carefully separate the Dual Magnet Support System (DMSS) and place
them on the clean glass.
3. Install cable protector wrapping around wave pump cable. This protects
the pump cable from triggerfish, urchins and other animals that may
damage pump cable (fig. 2).
4. Attach the AQAMAI pump and adjust it as desired.
5. If needed apply the adhesive cable clips on the external side of the
aquarium glass. Make sure the glass is clean first
INSTALLING THE AQAMAI CONTROLLER - POWER SUPPLY
1. Choose a location underneath your aquarium cabinet free of excessive
moisture and/or saltwater creep.
2. Using included wood mounting screw, mount the AQAMAI pump con-
troller to stand.
3. Connect the pump cable to the AQAMAI controller pump output cable
paying attention to align the two arrows on the connector before plugging
in. Then turn the locking nut screw.
4. Repeat the operation with the power supply cord.
5. Now you can connect the main plug to the wall socket.
6. The AQAMAI controller's led light on in white color for a while. Then
the yellow colour will appear when the default Constant Flow mode at
50% starts.
Description - fig. 3
A. Aquarium tank
B. Appliance
C. Power supply cord
D. Drip Loop
E. Attention
QUANTITY
Pomp
Controller
*According to your country standards
1
1
1
1
2
1
1