Behringer XeNyX 1202FX Guia De Inicio Rapido página 7

12
XENYX 1202FX/1002FX
XeNyX 1202FX/1002FX controls
Step 2: controls
This chapter describes the various control elements
(EN)
of your mixing console. All controls, switches and
connectors will be discussed in detail.
(1) MIC – Each mono input channel offers a
balanced microphone input via the XLR
connector and also features switchable
+48 V phantom power supply for condenser
microphones. The XENYX preamps provide
undistorted and noisefree gain as is typically
known only from costly outboard preamps.
(2) LINE IN – Each mono input also features
a balanced line input on a ¼" connector.
Unbalanced devices (mono jacks) can also be
connected to these inputs. Please remember
that you can only use either the microphone
or the line input of a channel at any one time.
You can never use both simultaneously!
(3) GAIN – Use the GAIN control to adjust the
input gain. This control should always be
turned fully counterclockwise whenever you
connect or disconnect a signal source to one
of the inputs.
(4) EQ – All mono input channels include a
3-band equalizer. All bands provide boost
or cut of up to 15 dB. In the central position,
the equalizer is inactive.
(5) LOW CUT – In addition, the mono channels
are equipped with a steep LOW CUT
filter designed to eliminate unwanted
low-frequency signal components.
(6) FX – FX sends enable you to feed signals via
a variable control from one or more channels
and sum these signals to a bus. The bus
appears at the console's FX send output and
can be fed from there to an external effects
device. The return from the effects unit is then
brought back into the console on the stereo
channels. Each FX send is mono and features
up to +15 dB gain. In the 1002FX/1202FX,
the FX send is routed directly to the built-in
effects processor. To make sure that the
effects processor receives an input signal,
you shouldn't turn this control all the way to
the left (-∞).
(7) PAN – The PAN control determines the
position of the channel signal within
the stereo image. This control features a
constant-power characteristic, which means
the signal is always maintained at a
constant level, irrespective of position in the
stereo panorama.
(8) LEVEL – The LEVEL control determines the
level of the channel signal in the main mix.
(9) CLIP – The CLIP LED's of the mono channels
illuminate when the input signal is driven
too high, which could cause distortion. If this
happens, use the GAIN control to reduce
the preamp level until the LED does not
light anymore.
LINE IN – Each stereo channel has two
(10)
balanced line level inputs on ¼" jacks for left
and right channels. If only the jack marked "L"
(left) is used, the channel operates in mono.
The stereo channels are designed to handle
typical line level signals. Both inputs will also
accept unbalanced jacks.
FX – The FX sends of the stereo channels
(11)
function similar to those of the mono
channels. However, since the FX send buses
are both mono, a mono sum is first taken from
the stereo input before it is sent to the FX bus.
BAL – The BAL(ANCE) control determines the
(12)
levels of left and right input signals relative
to each other before both signals are then
routed to the main stereo mix bus. If a channel
is operated in mono via the left line input,
this control has the same function as the PAN
control used in the mono channels.
+4/-10 – The stereo inputs of the XENYX
(13)
1002FX and 1202FX have an input sensitivity
switch which selects between +4 dBu and
-10 dBV. At -10 dBV (home-recording level),
the input is more sensitive (requires less level
to drive it) than at +4 dBu (studio level).
FX TO MAIN – The FX TO MAIN control feeds
(14)
the effects signal into the main mix. If the
control is turned all the way counterclockwise,
no effects signal is present in the sum signal of
the mixing console.
FX SEND – The FX SEND connector outputs
(15)
the signal you picked up from the individual
channels using the FX controls. You can
connect this to the input of an external
effects device in order to process the FX bus'
master signal. Once an effects mix is created,
the processed signal can then be routed
from the effects device outputs back into a
stereo input.
13
Quick Start Guide
PHONES/CONTROL ROOM – The stereo LEVEL INDICATOR – The high-precision
(16) (25)
PHONES jack (at the top of the connector 4-segment display accurately displays the
panel) is where you connect headphones. relevant signal level.
The unbalanced CTRL ROOM OUT jacks carry
SIGNAL and CLIP LED – The SIGNAL LED on
(26)
the summed effects and main mix signals,
the effects module shows the presence of a
as well as soloed channel signals. The
signal whose level is high enough. This LED
PHONES/CONTROL ROOM control adjusts the
should always be on. However, make sure
level of both headphones and main monitor
that the CLIP LED lights up only sporadically.
outputs.
If it is lit constantly, you are overdriving the
MAIN MIX – The MAIN OUT connectors are effects processor, which leads to unpleasant
(17)
unbalanced mono jacks. The main mix signal distortion. If this occurs, turn the FX controls
appears here at a level of 0 dBu. The MAIN MIX down somewhat.
fader adjusts the volume of these outputs.
PROGRAM – The PROGRAM control has two
(27)
CD/TAPE INPUT – The CD/TAPE INPUTs functions: by turning the PROGRAM control,
(18)
are used to bring an external signal source you dial the number of an effect. The number
(e.g. CD player, tape deck, etc.) into the of the preset you just dialed up blinks in the
console. They can also be used as a standard display. To confirm your selection, press the
stereo line input, so the output of a second PROGRAM control; the blinking stops.
XENYX or BEHRINGER ULTRALINK PRO MX882
can be connected.
CD/TAPE OUTPUT – These connectors are
(19)
wired in parallel with the MAIN OUT and carry
the main mix signal (unbalanced). Connect the
CD/TAPE OUTPUT to the inputs of your
recording device. The output level is adjusted
via the high-precision MAIN MIX fader.
CD/TAPE TO MIX – When the TAPE TO
(20)
MIX switch is depressed, the 2-track input
is assigned to the main mix providing
an additional input for tape machines,
MIDI instruments or other signal sources that
do not require any processing.
CD/TAPE TO CTRL ROOM – Press the CD/TAPE
(21)
TO CTRL ROOM/PHONES switch if you want to
monitor the 2-track input via the CTRL ROOM
OUT. This provides an easy way to monitor
signals coming back from tape to ensure that
they are recording correctly.
FX TO CTRL ROOM – If you want to monitor
(22)
only the FX send signal in your headphones
or monitor speaker(s), press the FX TO CTRL
switch. This mutes the main mix signal while
routing the FX SEND output to the monitor(s).
+48 V – The red +48 V LED lights up when
(23)
phantom power is on. The PHANTOM switch
activates the phantom power supply on the
XLR connectors of all mono channels.
POWER – The POWER LED indicates that the
(24)
console is powered on.