In Case Of Problems - Qlima SRE0031TC Instrucciones De Uso

3H OFF FUNCTION
When the heater is working and button
hours of operation (after pushing the button). During the countdown period this setting can be de-activated by
pushing the button again. In the display the status of this function is shown.
G
TURNING THE HEATER OFF
1. Press the ON / OFF button
check that the flame goes out.
G
The ventilator continues operating for about 3 minutes after turning off in order to cool the inside of the
heater. If you turn off the power earlier, uncontrolled symptoms can occur (release of smoke, smell etc.)..
H

IN CASE OF PROBLEMS

The symptoms mentioned above are not faults and not abnormal. Check the list.
Symptoms
Igniting is tedious
While igniting
Crackling sound
White smoke
Smoke and an unpleasant smell during first use
The ambient temperature does not increase and the requested
temperature is higher.
The flame glows red.
During ignition or The ambient temperature does not decrease and the requested
turning off temperature is lower.
The displayed ambient temperature is not the same as indicated by
a thermometer.
Small knocking noises when the heater is in operation or immedia-
tely after turning off.
Noise 8 seconds after turning off.
THE INFORMATION DISPLAY
The information display  not only serves as an indicator of the (set) time and temperature (sections C, E, and F), it
also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter:
Code Information
Time The heater has been automatically turned off by a power
---- cut or bad connection.
An earthquake (magnitude 5 or more), strong vibrations or
E01 a shock will ensure that the heater automatically
turns off. (The safety system against shocks has worked).
The heater has been automatically turned off after a fault
E02
or during ignition or due to the presence of water or dust
E03
in the fuel filter or in the fixed tank.
An increase in ambient temperature has turned the heater
E07
off. (The temperature monitoring system has worked).
The heater has been automatically turned off because the
Filter hot air stream, the ventilator or the ventilator filter is bloc-
E09 ked or hindered by something. (The safety system against
overheating has worked).
The heater has been turned off in a closed space. (The
E13
safety system against incomplete combustion has worked).
The ON indicator The heater has automatically stopped because the ON / OFF
flashes. Err lights up button was kept pressed in or was blocked.
F00 – F30 Poor functioning. Heater needs maintenance
4
28
is pushed, the heater will switch off automatically after three
22 22
. The red lamp flashes for about 8 seconds and the heater is turned off. Always
20 20
Causes
Igniting takes about 45 seconds. After filling the tank, wait till the fuel
has reached the fixed tank. Repeat ignition 2 or 3 times.
This sound is made by the electric ignition.
This can happen if the fuel does not circulate past the burner properly
That is the protective lacquer getting warm. This soon stops. Give the
space more ventilation.
The space is too large.
The ambient air is damp or salty or it contains too many impurities.
The heater is being used in a small insulated space or the outside tem-
perature is relatively high. Turn the heater off.
This is because the displayed ambient temperature is an indication of
the average temperature of the space.
This is the sound of the metal expanding.
A ticking sound: can occur when the heater cools off.
Action
Restore power or restore the connection. Press the ON / OFF
key 20 20
again.
Make sure there are no combustible materials around the
heater, or fuel leakages. Press the ON / OFF key 20
Remove the water and the dust in the fixed tank. Clean
the fuel filter (see chapter L). Press the ON / OFF button 20
again.
Ventilate the space. Let the heater cool off. Press the ON /
OFF button 20 20
again.
Remove obstacles from the ventilator opening. Clean the
ventilator filter (see chapter L) Press the ON/OFF button 20
again. If the problem occurs again after taking the above
measures, contact your dealer.
Ventilate the space and press the ON / OFF button 20
Ensure the space is sufficiently ventilated.
Remove obstacles around the buttons of the display panel.
Press the ON/OFF button 20 20
again.
Note the messages displayed and turn the heater off. Con-
tact your dealer.
20
again.
20
20
20
again.