Bellelli Leonardo Manual De Instrucciones página 20

Group 1 (from 9 to 18 kg) (Fig. 23 - 31)
Warning: The child seat must be installed in a
forward-facing position with respect to the
forward direction of travel of the vehicle.
EN
How to fit the child seat (Fig. 23 - 29)
Make sure that booster lever (N) is closed.
Place the child seat on the car seat. Position the
child seat so that it fits snugly on the car seat.
Warning: The car seat belt routing positions are
marked in red. Do not route the car seat belt in
positions other than those indicated.
Route the car seat belt between the base and
the child seat (fig. 23).
Fasten the car seat belt (fig. 24).
Insert the lap section of the car seat belt into
tensioner (A) located on the same side as the
car seat belt retractor reel (fig. 25).
Tension the belt fully. Check that the belt is not
twisted.
Insert the lap section of the car seat belt into
belt restraint guide (B) located on the same side
as the car seat belt retractor reel (fig. 26).
Check that the belt is completely inside the belt
restraint guide.
Close the belt restraint guide.
Thread the belt through belt guide (E) (fig. 27).
Repeatedly operate belt tensioner (A) until the
belt is taut with no slack (fig. 28).
Warning: For the maximum effectiveness it is
advisable to activate the belt tensioner as the
last step in the procedure.
Warning: after fastening the car seat belt
check the position of the buckle. The correct
position is shown in fig. 29. If the buckle is in
a different position, shift the child seat
sideways on the car seat until finding the
correct position. If you are in doubt, seek
assistance from the manufacturer or retailer.
How to remove the child seat from the car
(Fig. 30 - 31)
Unbuckle the car seat belt.
Squeeze the tabs at the side of belt tensioner
(A) and then push the lever downwards to
unlock the mechanism (fig. 30).
Pull the car seat belt to disengage it completely
from the belt tensioner (fig. 31).
Open belt restraint guide (B).
Pull the belt out of the child seat and allow it to
retract on the reel to complete the procedure.
How to position a child in the seat (Fig. 32 - 37)
Press adjuster (J) underneath the seat and
simultaneously pull both the harness straps (fig. 32).
Press the red button on buckle (I) to open it (fig. 33).
Lay the two halves of the buckle on the sides of
the child seat (fig. 34).
Place the child in the seat.
Bring the two tongues of the harness together.
Insert the tongues into buckle (I) (fig. 35). Correct
closing of the buckle is confirmed by a click.
Position the pads (H) on the shoulders and chest
of the child and pull them fully downward (fig. 36).
Pull the front adjuster strap (M) to tighten the
harness snugly over the child (fig. 37).
!!!Warning: During the journey periodically
check that the child has not managed to wriggle
out of the child seat.
How to free the child from the seat (Fig. 38- 39)
Press adjuster (J) underneath the seat and
simultaneously pull both the harness straps to
slacken them (fig. 38).
Press the red button on the buckle (I) to open it
(fig. 39).
Pull out harness straps and move them clear of
the child.
Maintenance (Fig. 40 - 46)
Take the covers off completely for washing.
To remove the cover:
Open the buckle (I) (fig. 40).
Pull out the harness straps from the back of the
child seat. Proceed as follows:
• Open cover (D) on the rear of the backrest
(fig. 41).
• Pull recline handle and simultaneously push
the child seat backwards so that it assumes
the fully upright position.
• Press adjuster (J) and simultaneously pull
both harness straps (fig. 42).
• Disengage the harness straps from the
metal yoke (C) at the rear of the child seat
backrest (fig. 43).
• Unthread the metal fitting and the shoulder
pad strap (P) through the child seat
backrest (fig.44 + 45).
Remove the cover, carefully disengaging:
• The harness straps and buckle tongues
through the side routing slots (fig. 46).
• The metallic plate that holds the buckle
through the seat routing slot.
18