U-HAUL 41929 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required: 1500 short bed model – hack saw
Fastener Kit: F41929
Wrenches: 3/4", 13/16", 15/16"
Drill Bits: 1/2"
FISHWIRE (SUPPLIED)
VEHICLE FRAME RAIL LONG BED
MODEL SHOWN THIS SIDE
HOLE TO BE DRILLED
LONG BED MODELS
s q
p
11
FISHWIRE CARRIAGE
BOLTS THROUGH SLOTS
IN FRAME – BOTH SIDES
SEE FIGURE 3
s
11
j
HEX BOLT 9/16-12 X 2.0" GR5
Qty. (2)
k
FLAT WASHER 9/16"
Qty. (2)
l
Qty. (2) BLOCK .375 X 1.50 X 3.00
m
Qty. (2) BLOCK .25 X 1.50 X 2.00
n
Qty. (2) LOCK WASHER 9/16
o
Qty. (2) HEX NUT 9/16-12
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2009, 2012 Cequent Performance Products
Installation Instructions
DODGE RAM PICKUP
WITH OR WITHOUT O.E.M. HITCH
BUMPER
O.E.M. RECEIVER
HOLES TO BE DRILLED
SHORT BED MODELS ONLY
BOTH HOLES TO BE DRILLED
SHORT BED MODELS ONLY
BUMPER BRACKET
ONLY
PLACE ITEM 3 BETWEEN
BUMPER BRACKET AND
HITCH SIDE BRACKET
AS REQUIRED
PUSH/SLIDE 1/4" THICK
BLOCKS THRUOGH END
OF FRAME-BOTH SIDES
SEE FIGURE 2
r p
Tighten all 1/2-13 fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Tighten all 9/16-12 fasteners with torque wrench to 110 Lb.-Ft. (149 n*m)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
FIGURE 1
p
CARRIAGE BOLT 1/2"-13 X 1.75 GR5
Qty. (6)
q
Qty. (2) BLOCK .25 X 1.50 X 3.50
r
Qty. (2) BLOCK .25 X 2.00 X 2.00
s
LOCK WASHER 1/2"
Qty. (6)
HEX NUT 1/2"
Qty. (6)
11
Sheet 1 of 6 N41929
Part Numbers:
41929
96929
Max Gross Max Tongue
Trailer WT (LB) WT (LB)
15000 (6810 Kg) 1500 (681 Kg)
12000 (5448Kg) 1200 (545 Kg)
VEHICLE FRAME RAIL SHORT BED
MODEL SHOWN THIS SIDE
j k l m n o
USE THIS HOLE FOR
2500/3500 MODELS
USE THIS HOLE FOR
1500 MODELS
OPTIONAL LOCKING STABILIZING PIN
J-PIN
PART No. 7651 (ORDER SEPARATELY)
6-1-12
Form: F205 Rev A 5-6-05
Rev. G