Enlaces rápidos
r
r
CSA B125
ASME A112.18.1
ICC/ANSI A117.1
Models/Modelos/Modèles
6572828, 6472720
Series/Series/Seria
Lokit
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
For easy installation of your
BRIZOt faucet you will need:
* To READ ALL the instructions completely before
beginning.
* To READ ALL warnings, care, and maintenance
information.
* To purchase the correct water supply hook--up.
Para instalación fácil de su llave
BRIZOt usted necesitará:
* LEER TODAS las instrucciones completamente
antes de empezar.
* LEER TODOS los avisos, cuidados, e información
de mantemiento.
* Comprar las conexiones correctas para el suministro
de agua.
Pour installer votre robinet BRIZOt
facilement, vous devez :
* LIRE TOUTES les instructions avant de débuter.
* LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien.
* Acheter le bon raccordement nécessaire pour
l'alimentation en eau.
12612.00
TWO HANDLE LAVATORY AND BAR FAUCETS
t
MEZCLADOR PARA FREGADERO
MELANGEUR A DOUBLE COMMANDE POUR LAVABO
ET BAR
6572828
You may need/Usted puede necesitar/
Articles dont vous pouvez avoir besoin:
2 mm, 2.5 mm, 3 mm
Note: This faucet fits 1 3/8" min.
mounting hole size.
Note: Ce robinet va dans un trou
d'installation de 1 3/8" au minimum.
Nota: Es possible montar la unidad en
un orificio de 1 3/8".
1
6472720
Note: The back edge of the faucet body
must be at least 1" from the backsplash
on wall in order to allow acces to the lift
rod function.
Nota: La orilla posterior del mecanismo/
cuerpo de la llave de agua debe estar
por lo menos a 1" del protector de yeso
de la pared para poder permitir acceso
a la función de la barrita para levantar el
desagüe automático.
Note: Le côté arrière du corps du robi-
net doit se trouver à au moins 1 po du
dosseret sur le mur pour que la tirette
puisse bouger
02.08
Manuales relacionados para Brizo Loki 6572828 Serie
Resumen de contenidos para Brizo Loki 6572828 Serie
- Página 1 TWO HANDLE LAVATORY AND BAR FAUCETS MEZCLADOR PARA FREGADERO MELANGEUR A DOUBLE COMMANDE POUR LAVABO ET BAR CSA B125 ASME A112.18.1 ICC/ANSI A117.1 Models/Modelos/Modèles 6572828, 6472720 Series/Series/Seria Lokit 6572828 6472720 Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
-
Página 2: Faucet Installation
1/2” (12.70mm) IPS Fig. 1. Fig. 2 FAUCET INSTALLATION MAKE CONNECTIONS TO WATER LINES: A. For Lavatory faucets: Install lift rod. Insert the threaded end of the rod in the hole Choose hook--ups for 1/2” I.P.S. connections: from underneath the faucet and screw it into the lift rod knob. Hand tighten only. (1) Ball nose riser (3/8”... - Página 3 Fig. 3 POP--UP INSTALLATION E. Place white plastic seal (8) into body (9) and screw body (9) onto flange (3). A. Remove plastic stopper cap (1) and stopper (2) from flange (3). Note: Pivot (16) must face faucet. Pull assembly down and tighten nut/washer/ B.
- Página 4 Fig. 4 Fig. 5 FLUSH YOUR SYSTEM MAINTENANCE, SPOUT. Remove aerator (1) and turn faucet handle (2) to the full on mixed position. To replace your spout assembly or if the faucet leaks around the base of the Turn on hot and cold water supplies and flush water lines for one minute. spout, perform the following steps: Important: This flushes away any debris that could cause damage to internal A.
- Página 5 Fig. 6 MAINTENANCE, HANDLE COVER. To replace a handle cover, perform the following steps: A. There is a small hole (4 mm) on the bottom side of the handle cover. Locate the hole with your finger and with the tip of a small Allen wrench push up on the tab inside this hole and pull the cover off horizontally as shown.
- Página 6 Fig. 7 MAINTENANCE, CERAMIC VALVES. If your faucet leaks out of the end of the spout, perform the following steps: Note: Determine if your spout is leaking hot or cold water by checking the water dripping out of the spout. Turn off the water supplies before working on your faucet.
- Página 7 Fig. 8 MAINTENANCE, CERAMIC VALVES, REASSEMBLY. A. When inserting the new cartridge into the body, please pay special attention to the flats (NB!) on the cartridge and body. These must be aligned in order to fully seat the cartridge. In addition, as you are pushing the new cartridge in place, the stem lever must be aligned and oriented as shown in view above before the cartridge is fully seated in place.
- Página 8 Fig. 9 MAINTENANCE, SLIDE HANDLES, REASSEMBLY. A. Important: Make sure that the lever coming from the stem is pushed all the way to the back of the slot on the body. See view above. Align the opening in the tab at the back of the handle assembly with the tip of the stem lever and push the handle assembly in place.
- Página 9 6472720 6572828 RP 44132s Lavatory Spout, Complete Surtidor completo para el Lavamanos Bec complet pour robinet de lavabo RP 44133 Guide & O--Rings for Spout Guía y Aros O para el Surtidor Guide et joints toriques pour bec RP 44134 Support ring for spout Aro de Soporte para el Surtidor Anneau d’appui pour bec...
- Página 10 This warranty excludes all industrial, commercial and business usage, whose purchasers are parts may be obtained by calling 1--877--345--BRIZO (2749) (in the U.S. and Canada) or by hereby extended a five year limited warranty from the date of purchase, with all other terms of writing to: this warranty applying except the duration of the warranty.