Idiomas disponibles
Idiomas disponibles
The color-coded rings of receptacles and connectors
include a cap. The color-coded rings of plugs and
inlets do not include a cap.
Color-coded ring on plug side
Cap with color-coded ring on receptacle side
Rated current and voltage markings
It is essential to indicate the current and voltage of
the main circuit on the supplied stickers. Apply the
stickers on or adjacent to the product so they can
easily be seen.
OPERATION
To ensure safe and reliable operation,
MELTRIC plugs and receptacles must be used
in accordance with their assigned ratings.
They can only be used in conjunction with mating
receptacles or plugs manufactured by MELTRIC or
another licensed producer of products bearing
the
technology trademark.
WARNING
Connection
DANGER
First check to see that the power source is
CAUTION
de-energized. DO NOT ENGAGE ON AN
ENERGIZED CIRCUIT.
NOTICE
Orienttheplugsothecontactwillfitintotherecepta-
clefigure1.Pushtheplugpartiallyintotherecepta-
ADVERTENCIA
cle and rotate the plug counterclockwise until it hits a
stopfigure2.Theninsertplugfullyintoreceptacle
DANGER
WARNING
and rotate clockwise about one quarter turn until the
locking pin engages into the slot on the receptacle
DANGER
CAUTION
figure3.
CAUTION
AVISO
NOTICE
ADVERTENCIA
DANGER
CAUTION
Insert
AVISO
Twist until
pin locks
Disconnection
First check to see that the power source is
de-energized. DO NOT DISCONNECT ON
AN ENERGIZED CIRCUIT.
Insert unlocking key onto locking pin as shown in
figure4.Disengagelockingpinbyslidingunlocking
keyasshowninfigure5.Whenlockingpinisre-
leased, hold unlocking key in position and twist plug
WARNING
counterclockwise about 30° as shown in
figure6.Afterturning,withdrawplug.
DANGER
CAUTION
NOTICE
ADVERTENCIA
DANGER
CAUTION
AVISO
1
PADLOCKING OPTION
Assembly
Place the locking ring as shown:
Watertightness
gasket
2
Twist then
insert
Operation
Connect the product equipped with the locking ring,
insert the shaft and padlock it.
3
Insert
unlock
tool
4
5
Retract
locking
pin
6
Twist &
Remove
Lug
Locking ring
Color-coded ring
MAINTENANCE
Before inspecting, repairing,
or maintaining MELTRIC
products,disconnect electrical
power to the receptacle to eliminate the risk of elec-
WARNING
trical shock.
DANGER
MELTRIC products require little on-going mainte-
nance. However, it is a good practice to periodically
CAUTION
perform the following general inspections:
• Check the mounting screws for tightness.
NOTICE
• Verify that the weight of the cable is supported
ADVERTENCIA
by the strain relief mechanism and not by the ter-
minal connections.
DANGER
• Check the IP gaskets for wear and resiliency.
Replace as required.
CAUTION
• Verify the electrical continuity of the ground circuit.
AVISO
• Check the contact surfaces for cleanliness
and pitting.
Deposits of dust or similar foreign materials can be
rubbed off the contacts with a clean cloth. Sprays
should not be used, as they tend to collect dirt. If
anysignificantpittingofthecontactsorotherserious
damage is observed, the device should be replaced.
Receptaclecontactsmaybeinspectedbyaqualified
electrician. This should only be done with the power off.
MANUFACTURER'S RESPONSIBILITY
MELTRIC's responsibility is strictly limited to the
repair or replacement of any product that does not
conformtothewarrantyspecifiedinthepurchase
contract. MELTRIC shall not be liable for any pen-
alties or consequential damages associated with the
lossofproduction,work,profitoranyfinancialloss
incurred by the customer.
MELTRIC Corporation shall not be held liable when
its products are used in conjunction with products not
bearing the
technology trademark. The use
of MELTRIC products in conjunction with mating
devices that are not marked with the
technology trademark shall void all warranties on
the product.
MELTRIC Corporation is an ISO 9001 certified com-
pany. Its products are designed, manufactured and
rated in accordance with applicable UL, CSA and IEC
standards. MELTRIC designs and manufactures its
products in accordance with Marechal keying standards
established to ensure intermateablility with similarly
rated products manufactured by Marechal Electric
Group.
INSCS1000 G
