Manuales relacionados para Techne HB-1D
Resumen de contenidos para Techne HB-1D
- Página 1 HB-1D Hybridiser Operator’s Manual Issue 25 Date of issue: 3rd May 2005 Techne is a trademark © Techne, 2003...
-
Página 3: Tabla De Contenido
H B - 1 D O P E R A T O R ’ S M A N U A L CONTENTS HB-1D issue 20 onwards Operator's Manual page SAFETY AND INSTALLATION English Français Deutsch Español Italia INTRODUCTION Initial checks... - Página 4 H B - 1 D O P E R A T O R ’ S M A N U A L...
- Página 5 H B - 1 D O P E R A T O R ’ S M A N U A L NOTES...
-
Página 6: User Maintenance
Notwithstanding the description and specification(s) of the units Techne have taken great care in the design of these units to contained in the Operator’s Manual, Techne hereby reserves protect operators from hazards, but users should pay attention to... -
Página 7: Français
L’appareil est garanti contre tout défaut ou vice de fabrication Techne a apporté un soin tout particulier à la conception de ces pour la durée figurant sur la carte de garantie, à compter de la appareils de façon à... -
Página 8: Deutsch
Unfall zugrundeliegt. Der unter diese Garantie fallende Service und brennbare Materialien können sich leicht entzünden. wird vom Lieferanten geleistet. Techne hat bei der Konstruktion dieses Gerätes sehr darauf Ungeachtet der in dieser Gebrauchsanweisung enthaltenen geachtet, daß der Bediener vor Gefahren geschützt ist. Dennoch Beschreibungen und Spezifikationen, behält sich Techne hiermit... -
Página 9: Introducción
Techne ha puesto gran cuidado en el diseño de estos aparatos A pesar de la descripción y las especificaciones de los aparatos para proteger al usuario de cualquier peligro; aún así se deberá... -
Página 10: Italia
Questo Manuale è stato realizzato esclusivamente a vantaggio · Utilizzare con attenzione e indossare guanti protettivi; dei clienti della Techne e in alcun modo potrà essere utilizzato · Non mettere vicini oggetti caldi o oggetti infiammabili; come garanzia, condizione o rappresentazione concernente la ·... -
Página 11: Introduction
HB-1D comes with adjustable feet to enable accurate levelling. Initial Checks When you receive your new HB-1D remove all the packing. Check the unit for any transit damage. If there is any transit damage at all inform Techne Sales Department or your Techne dealer immediately. -
Página 12: Specification
# Large tubes are fitted with 70°C seals, seals part number 6101488 are required to work to 100°C. For the Hybridisation Tubes see the list under Accessories Working conditions The HB-1D is designed to work safely under the following conditions: Ambient temperature range 5°C to 40°C Humidity Up to 95% relative humidity, non-condensing Note: The control specifications are quoted at an ambient temperature of 20°C. -
Página 13: Unpacking
H B - 1 D O P E R A T O R ’ S M A N U A L Unpacking Ensure that the following have been removed from the packing: • The Hybridiser. • Drip Tray (not Techne Inc). • Power Lead. • Guarantee Card. • Decontamination Certificate. - Página 14 H B - 1 D O P E R A T O R ’ S M A N U A L SPEED CONTROL...
-
Página 15: Warning
11. Servicing by Techne and their Agents Please note that neither Techne nor any of their agents can accept the return of ANY GLASSWARE from these units. If the unit is returned it must be thoroughly decontaminated and a... -
Página 16: Switching On
H B - 1 D O P E R A T O R ’ S M A N U A L Switching On Once your HB-1D is connected to a power supply, switch it on using the power switch next to the power inlet socket on the rear panel. -
Página 17: Operation
Remove the tube end cap which has the holes in it. Place the filters in the tube and replace the end cap. A small quantity of Techne O-ring grease, see the list of accessories, must be smeared on the seal to facilitate the insertion of the end cap. - Página 18 H B - 1 D O P E R A T O R ’ S M A N U A L Small Tube (3 x 44mm dia) assembly Unscrew the tube end cap. Place the filters in the tube and replace the end cap.
-
Página 19: The Hb-1D
H B - 1 D O P E R A T O R ’ S M A N U A L The HB-1D Insert the tubes or tube holder into the HB-1D ensuring that they rotate freely and engage on the drive rollers. -
Página 20: The Front Panel Controls
H B - 1 D O P E R A T O R ’ S M A N U A L The Front Panel Controls The front panel controls consist of three buttons for controlling the display, a four digit LED display and three indicators. The SET temperature Button TEMPERATURE ∇... -
Página 21: Power Indicator
H B - 1 D O P E R A T O R ’ S M A N U A L Tube temperature NOTE: It takes approximately 50 minutes for the interior of the hybridisation tubes to reach the displayed temperature depending upon the number of filters and amount of hybridisation fluid used. -
Página 22: Basic Protocol For Southern Hybridisations
H B - 1 D O P E R A T O R ’ S M A N U A L BASIC PROTOCOL FOR SOUTHERN HYBRIDISATIONS * INSERTION OF FILTERS Place a wet or moist filter, DNA side facing inwards, into a hybridisation tube and allow it to adhere to the glass. -
Página 23: Technical Information
Techne Service department giving as much information as possible to help diagnose the fault. Please remember to return the unit in its original packing, Techne accept no responsibility for damage to units which are not properly packed: if in doubt, contact your supplier. - Página 24 Before cleaning your unit ALWAYS disconnect from the power supply and allow to cool. You can clean the case of the HB-1D with a cloth dampened in soapy water or ethanol. No part of the unit should be immersed in solvents. Do not use acetone or abrasive cleaners.
-
Página 25: Accessories And Spares
H B - 1 D O P E R A T O R ’ S M A N U A L Accessories and Spares The following may be purchased from Techne or their dealers. All Techne tubes are made from Borosilicate glass... - Página 26 H B - 1 D O P E R A T O R ’ S M A N U A L...